Re: Reg. USB Driver while booting wince 5.0

On Feb 3, 9:45 pm, "Anthony Pellerin"
<apellerin@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
You have a null stub display driver in your catalog. Add this component to
your OsDesign an sysgen.

HTH

--
--
--
----------------------------------------------------------------
Anthony Pellerin (eMVP)
ADENEO (ADESET)
Windows Embedded Consultant
<apellerin AT adeneo DOT adetelgroup DOT com>http://www.adeneo.adetelgroup..com
Tél  : +33 (0)4.72.18.57.77
Fax : +33 (0)4.72.18.57.78
----------------------------------------------------------------
<vinayagamenm...@xxxxxxxxx> a écrit dans le message de news:
aaa1fd91-e8da-4e1c-82c5-1be1dc517...@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx



Hi,
   I have a evaluation board with s3c2440 CPU i wrote USB driver for
it.
  My USB driver is working in my evaluation board and i was able to
connect activesync.

  I have a same USB device in my target board i just changed
config.bib only
  But my USB driver is not working and i was not able to connect
active sync.

Further when i load OS built in debug mode i am getting the following
message

I am getting the following debug messages.

2
DEBUG: CreateSerialObject 1
BSP Interrupt Enable IRQ
DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn
\Serial2\BusPrefix) returned 2
DEBUG: CreateSerialObject 2
BSP Interrupt Enable IRQ
DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn\MSFlash
\BusPrefix) returned 2

DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn\OHCI
\BusPrefix) returned 2
HCD driver DLL attach
HCD!HCD_Init
OHCD: Read config from registry: Base Address: 0x49000000, Length:
0x1000, I/O Port: NO, SysIntr: 0x11, Interface Type: 0, Bus Number: 0
OHCD: ioPhysicalBase 0x49000000, IoSpace 0x0
OHCD: ioPortBase 0x230000, portBase 0x49000000
DMA buffer passed in from PDD
USBD: DLL attach
+USBD:HcdAttach, hcd: 0x399A0
-CDevice::Initialize, success!
+CHW::Initialize base=0x230000, intr=0x11
BSP Interrupt Enable IRQ
-CHW::Initialize, success!
+CPipe::Initialize
-CPipe::Initialize. Success!
+CHW::EnterOperationalState
-CHW::EnterOperationalState
-COhcd::Initialize. Success!!
DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn\IOD
\BusPrefix) returned 2
IOD: DLL_PROCESS_ATTACH
IOD : DLL_PROCESS_ATTACH
::: IOD_Init
DeviceFolder::LoadDevice!Enumerate Found deprecated load instructions
at (Drivers\BuiltIn\AFD). Driver cannot be unloaded.
!AFD:AfdInitialize: Can't open Registry key Comm\AFD -- creating
'Stacks' entry

USB Device Init
[NOTIFY] HandleSystemEvent 7 /ADD NTP0:
[NOTIFY] SetUserNotification::Registring system watch: event 12 app \\.
\Notifications\NamedEvents\DSTTzChange args AppRunAfterTzChange
IRQ = 6, SYSINTR = 20
[NOTIFY] SetUserNotification (or replacing 00000000)
UsbFnMdd!UFN_Init: PDD has 5 endpoints
[NOTIFY] SetUserNotification::Registring system watch: event 1 app \\.
\Notifications\NamedEvents\DSTTimeChange args AppRunAfterTimeChange
UsbFnMdd!UFN_Init: PDD supports speeds 0x1
[NOTIFY] RemoveAppRunAtTime::Starting Database Sweep...
UsbFnMdd!CUfnBus::CreateChild: Using client driver key "\Drivers\USB
\FunctionDrivers\Serial_Class"
[NOTIFY] SetUserNotification (or replacing 00000000)
[NOTIFY] HandleSystemEvent 7 /ADD UFN1:
DEVICE!RegReadActivationValues RegQueryValueEx(\Drivers\USB
\FunctionDrivers\Serial_Class\BusPrefix) returned 2
[NOTIFY] SetUserNotification::Setting event semaphore
UsbFnMdd!UfnMdd_RegisterDevice: Device registered
[NOTIFY] ProcessDatabase::started at local time 01/01/2003 12:00:03
UsbFnMdd!CPipe::Open: Opened pipe (0x0004efc0): physical address 0,
bus address 0x00
BSP Done IRQ
BSP Interrupt Enable IRQ
BSP Done IRQ
UsbFnMdd!UfnMdd_Start: Function controller running
UsbFnMdd!CUfnBus::ActivateChild: Activated client driver
"Serial_Class"
DEVICE!RegReadActivationValues RegQueryValueEx(Drivers\BuiltIn
\CS8900\BusPrefix) returned 2
NDIS:ndisAddPCMCIADevice INdisOpenDeviceKey failed
NDIS:: CE_AddBusFriendlyName() [successfully created] [HKLM\Comm
\BusFriendlyNames\BuiltInPhase1_0_17_0\CS8900]
NDIS: ERROR: CEDeviceInit() no BusNumber for [Comm
\BuiltInPhase1\CS8900\Parms]
DEVICE!LaunchDevice: Init() failed for device 0x00050ca0
DEVICE!I_ActivateDeviceEx: couldn't activate: prefix NDS, index 1, dll
ndis.dll, context 0x802e7dc
[NOTIFY] HandleSystemEvent 7 /ADD COM5:
TAPI:OldAddTapiDevice - This BSP is loading TSPs by old method!!!
Change registry settings to use new way!!!
FILESYS: SignalStarted loop = 2
FILESYS: Launching gwes.exe
Ceddk!CalibrateStallCounter: Enter
Ceddk!CalibrateStallCounter: Stall counter loaded from registry(1000)
System Default HKL value set to 00000409
Grow Gdi handle table from 0 to 64
LogFontFromRegistry(SYSTEM\GDI\SysFnt), lfHeight = -12Unknown:
DEBUGCHK failed in file c:\macallan\private\winceos\coreos\gwe\mgdi
\base\driver.cpp at line 1363
*** COULD NOT LOAD DISPLAY DRIVER (ddi.dll)! ***
*** SYSTEM BOOT ABORTING! ***
Unknown: DEBUGCHK failed in file c:\macallan\private\winceos\coreos\gwe
\mgdi\base\gdi.cpp at line 2075
Unknown: DEBUGCHK failed in file c:\macallan\private\winceos\coreos\gwe
\mgdi\base\bmpbase.cpp at line 689
Data Abort: Thread=8dc85cdc Proc=8c05c400 'gwes.exe'
AKY=00000011 PC=000b73e4(gwes.exe+0x000a73e4) RA=000a35f8(gwes.exe
+0x000935f8) BVA=0a000008 FSR=00000007
Main thread in proc 4dc85a1a faulted, Excpetion code = c0000005,
Exception Address = 000b73e4!
Main thread in proc 4dc85a1a faulted, WMGR not on line!
Main thread in proc 4dc85a1a faulted - cleaning up!
BSP Done IRQ
UsbFnMdd!CPipe::Open: Opened pipe (0x0004f038): physical address 1,
bus address 0x81
UsbFnMdd!UfnMdd_OpenPipe: Opened endpoint 0x81
UsbFnMdd!CPipe::Open: Opened pipe (0x0004f0b0): physical address 2,
bus address 0x02
UsbFnMdd!UfnMdd_OpenPipe: Opened endpoint 0x2

When i plug in USB cable i am getting the above message.
After that my USB is not recognized.

Is it because of display driver my USB is not working or anyother
reason.
If its because of display driver my system is aborting how can i
remove ddi.dll.

Suggest me to resolve my USB driver

Regards,
Vina- Hide quoted text -

- Show quoted text -

Hi,
Can you suggest me how to add "Null stub display driver" to OS
design.
I added enviromment variable BSP_NODISPLAY =1.
But still my Active sync is not connecting.

Regards,
Vinayagam.
.

Relevant Pages