Re: Connect to PDA without ActiveSync
- From: "Bruce Eitman [eMVP]" <beitman.nospam@xxxxxxxxxxxxxxxxxxxxxx>
- Date: Fri, 16 Nov 2007 08:34:10 -0500
We are back to ask the OEM. You have turned your device into a paperweight,
and only the OEM can help you now.
--
Bruce Eitman (eMVP)
Senior Engineer
beitman AT applieddata DOT net
Applied Data Systems
www.applieddata.net
An ISO 9001:2000 Registered Company
Microsoft WEP Gold-level Member
"Thomas" <Thomas@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:6125C2BE-2684-47A1-B9E5-E4C33511BFC4@xxxxxxxxxxxxxxxx
The device have a internal flash memory ( unfortunately fix on the board,
no
card)
It is called
\Storage card
In this dir the map and the navigation software resides. There is also a
AutoRunCE.ini in this directory. In that you define a startup program. In
this case I changed that from XNavigatorMenu.exe to \Windows\Explorer.exe
that worked very well on all devices that I have. But then I start to copy
a
new map(files) to that directory and that stopped after a while I guess
because the Storage card was full. The whole device stop to work, I cn
only
reset it. After that the system looks like it comes up, bit it never shows
the explorer anymore nor it start the ActiveSync Daemon. On the PC I get a
signal that a USB Device is connect but no ActiveSync came up. I guess th
ereason is simple. There is no more place for the system. But how can I
delete files ? To bad that the flash is fixed on the board.
thomas
"Bruce Eitman [eMVP]" wrote:
It is a question of the programmer, and that was the OEM. You could
theoretically modify it if you have enough information about the
hardware.
Typically the OEM does not provide enough information.
Maybe you should tell us what you are doing. So far you have told us
that
you put "something" in the flash and then the device failed to boot
fully.
Not much to go on.
--
Bruce Eitman (eMVP)
Senior Engineer
beitman AT applieddata DOT net
Applied Data Systems
www.applieddata.net
An ISO 9001:2000 Registered Company
Microsoft WEP Gold-level Member
"Thomas" <Thomas@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:ABDE49FB-3305-4497-8E12-6D4DF97D579C@xxxxxxxxxxxxxxxx
Does this mean , if the producer of that hardware only implement the
possibility to comunnicate via Activesync, there is no other way ? But
what
happens in Windows CE if a USB is beeing avaible(just pluged in) ?
Is'nt
it a
question to the programmer of CE ?
Thomas
"Bruce Eitman [eMVP]" wrote:
This is a question for the OEM.
--
Bruce Eitman (eMVP)
Senior Engineer
beitman AT applieddata DOT net
Applied Data Systems
www.applieddata.net
An ISO 9001:2000 Registered Company
Microsoft WEP Gold-level Member
"Thomas" <Thomas@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:C52A8FCF-2CD3-4CF0-B031-802F32DC359F@xxxxxxxxxxxxxxxx
I have a PDA/PDN (Falk Navigator) that I can't connect, it worked
until
I
put
something on the internal flash disk. Since then I only get the
Windows
start
splash screen and nothing else. If I plug in the device into a PC,
the
PC
load MS USB Snyc and tell me that at the systray but Active Sync
did'nt
found
the device, I think because the PDA did'nt start his ActviceSync
component. I
s there any chance to connect to the PDA ? It has Windows CE 5 Core
on
it.
I
have more of these devices all work correct accept that one.
Thomas
.
- References:
- Re: Connect to PDA without ActiveSync
- From: Bruce Eitman [eMVP]
- Re: Connect to PDA without ActiveSync
- From: Bruce Eitman [eMVP]
- Re: Connect to PDA without ActiveSync
- From: Thomas
- Re: Connect to PDA without ActiveSync
- Prev by Date: DDGPE driver for CE 6.0
- Next by Date: Re: Moving a project from public to private PB5.0
- Previous by thread: Re: Connect to PDA without ActiveSync
- Next by thread: Re: distinguishing between stream interface drivers
- Index(es):
Relevant Pages
|
|
