Re: USB boot, RNDIS issue, can't download image,How to install NAT tab

Tech Tip: Click here to run a free scan for Windows Errors and optimize PC performance

if your platform builder is in another computer, use windows internet
share.
if your device plug directly to your platform builder machine, you need to
config a ip address for the usb network interface.
you may see it as local area network 2 or so.

"How to install NAT table on my ethernet?"
<HowtoinstallNATtableonmyethernet@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in
message news:BC9444C2-E2FF-41AB-B54A-DE3781CB6D8D@xxxxxxxxxxxxxxxx
Hello,

software: wince5.

Hi. My eboot uses USB RNDIS to download the OS image into the target. The
initialization works, as you can see from the following output:


Enter your selection: d
INFO: Trying to initialize USB RNDIS.
HostMiniInit:: !!
Rndis:: initialization: with addr=0
Rndis:: initialization!
Rndis:: PDDInit Success!
Rndis:: Get MAC address F0F2,F200,20
Rndis:: Waiting some time for ISR:
RndisMdd:: PDD's max RX buffer = [8192] bytes.

Rndis:: initialization: Success
HostMini:: New filter set: [0x0] --> [0x20]

HostMini:: New filter set: [0x20] --> [0x0]

HostMini:: New filter set: [0x0] --> [0xB]

HostMini:: New filter set: [0xB] --> [0x0]

HostMini:: New filter set: [0x0] --> [0xB]

HostMini:: New filter set: [0xB] --> [0x2B]

HostMini:: New filter set: [0x2B] --> [0xB]

HostMini:: New filter set: [0xB] --> [0x2B]

INFO: MAC address: F2-F0-0-F2-20-0
System ready!
Preparing for download...
+OEMPreDownload()
INFO: Using device name: 'MAINSTN8192'
+EbootSendBootmeAndWaitForTftp
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255

The problem is the following: I am not able to download the image via
Platform Builder, that is, when i click on Attach Device and the download
dialog appears, nothing happens. What can I do?

By the sniffing of the netork interface used to connect PC and target I
can
see:
- target sends broadcast packet on UDP (srcport 980 dstport 980)
- host replys with UDC packet (srcport 1853 dstport 980)
The funny thing is that I tried 3 other pc, and only one (it is not mine
so
i do not know its configuratiuon) works.Any idea?

I heard someone had resolve this problem: it was necessary to install a
NAT
table on my ethernet nic.

How to install NAT table on nic?

Thankyou very much!

Albert
Freescale


.

Relevant Pages

  • Re: Download OS image to target with USB RNDIS
    ... initialization works, as you can see from the following output: ... Trying to initialize USB RNDIS. ... Sent BOOTME to 255.255.255.255 ... Platform Builder, that is, when i click on Attach Device and the download ...
    (microsoft.public.windowsce.platbuilder)
  • Re: Download OS image to target with USB RNDIS
    ... "Download" should say "Ethernet" Then click settings. ... While the bootme message is being sent there should be a network interface with the "Device Name" of "Microsoft Windows CE RNDIS virtual adapter". ... initialization works, as you can see from the following output: ...
    (microsoft.public.windowsce.platbuilder)
  • Re: about the transfer speed of the usb-serial function drive
    ... zhoumc wrote: ... I have had the RNDIS component on my CE device, but I have not seen the "dynamic network connection" yet. ... If you have the DHCP service running the IP config ...
    (microsoft.public.windowsce.platbuilder)
  • Re: about the transfer speed of the usb-serial function drive
    ... I have had the RNDIS component on my CE device (maybe ... but I have not seen the "dynamic network ... If you have the DHCP service running the IP config ...
    (microsoft.public.windowsce.platbuilder)
  • Re: about the transfer speed of the usb-serial function drive
    ... activesync does not use the network connection to make connecting. ... Alltough ActiveSync 4.x supports RNDIS as primary transport, ... If you have the DHCP service running the IP config ...
    (microsoft.public.windowsce.platbuilder)