NIC fails in RELEASE build CE 5.0

I have a CEPC-GEODE PC/104 board with an NE2000 ISA NIC. When I use the
VMINI driver in a debug build it works fine. In the release build, DHCP
fails. Searching, it seems that similar problems are form not removing the
vmini driver and KITL formthe build. I have done this--at least I think I
have.

Static IP also doesn't work--the board won't respond to a ping.

Here is what I have done in the build:

IMGNOKITL=1 (UN-check box - Build Options)
KERNELNOSHAREETH=1
BSP_NOSHAREETH=1
BSP_NIC_NE2000_ISA=1

I also have:

BSP_NOPCIBUS=1
BSP_NOPCMCIA=1 (These are also in the debug build)


In the DEBUG Build, none of these are set.
In the registry, I hav left the default settings, with the exception of
setting port (0x2c0) and IRQ (5) as follows:
[HKEY_LOCAL_MACHINE\Comm\NE2000]
"DisplayName"=LOC_DISPLAYNAME_COMM_NE2000
"Group"="NDIS"
"ImagePath"="ne2000.dll"

[HKEY_LOCAL_MACHINE\Comm\NE2000\Linkage]
"Route"=multi_sz:"NE20001"

[HKEY_LOCAL_MACHINE\Comm\NE20001]
"DisplayName"=LOC_DISPLAYNAME_COMM_NE20001
"Group"="NDIS"
"ImagePath"="ne2000.dll"

[HKEY_LOCAL_MACHINE\Comm\NE20001\Parms]
"BusNumber"=dword:0
"BusType"=dword:1
"InterruptNumber"=dword:05
"IoBaseAddress"=dword:2C0
"Transceiver"=dword:3
"CardType"=dword:0

[HKEY_LOCAL_MACHINE\Comm\NE20001\Parms\TcpIp]
"EnableDHCP"=dword:1
"DefaultGateway"=""
"UseZeroBroadcast"=dword:0
"IpAddress"="0.0.0.0"
"Subnetmask"="0.0.0.0"

The CE board sends a "DHCP Discover message", and it gets an Offer message
from the DHCP server, but the message is ignored--I never see a DHCP
Request--instead it sends several more "DHCP Discover" messages.

I enabled serialDebug, but kept :
KERNELNOSHAREETH=1
BSP_NOSHAREETH=1
I get debug message through the serial port and I can see that the NIC is
initialized and DHCP loads and tries to DHCP, but never sees the replys from
the DHCP server (They are sent)

It looks like the board cannot receive any data.

I am really stuck on this one!

thx


.

Relevant Pages

  • Re: 1720 and comcast
    ... logging buffer 10000 debug ... Verify that the "outside" interface connected to the cable modem is ... Enable DHCP debugging ...
    (comp.dcom.sys.cisco)
  • Re: NIC fails in RELEASE build CE 5.0
    ... it isn't included in the registry anywhere. ... And in the SerialDebug version it is never loaded. ... VMINI driver in a debug build it works fine. ... In the release build, DHCP ...
    (microsoft.public.windowsce.platbuilder)
  • Re: Damn you, FEDEX! or Nikon D40 lost in Springfield, MO blackhole.
    ... the 2 mp Mavica he had been using with a Nikon D40. ... After shopping around, he got me to order one for him. ... The shipper had it insured, but from what I have read it could take weeks to sort this crap out. ... You may get your insurance from FedEx and a couple weeks later they find it and deliver it. ...
    (alt.photography)
  • Re: NIC fails in RELEASE build CE 5.0
    ... VMINI driver in a debug build it works fine. ... IMGNOKITL=1 (UN-check box - Build Options) ... The CE board sends a "DHCP Discover message", ...
    (microsoft.public.windowsce.platbuilder)
  • Re: dhcp cisco806 basic setup question/problem...
    ... ip route 0.0.0.0 0.0.0.0 dhcp ... debug DHCP ... logging buffer 10000 debug ...
    (comp.dcom.sys.cisco)