Re: Stream Device Driver How-to

Do you get any other debug output?
Do you have Ship build set in the project settings? (you don't want this)
What are your registry settings?
If the messages are in fact DEBUGMSGs, is it a debug build?
Do you have the dpCurSettings mask set to allow the output?

--
Bruce Eitman (eMVP)
Senior Engineer
beitman AT applieddata DOT net

Applied Data Systems
www.applieddata.net
An ISO 9001:2000 Registered Company
Microsoft WEP Gold-level Member

"Phil" <pclaydon@xxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:C4254654-B885-4A7B-BF72-1DDDD1F5049A@xxxxxxxxxxxxxxxx
Thanks All

This has now been resolved after my latest Clean Sysgen. My DLL is now in
my
image and the registry on the target shows the correct entries. However, I
expected to see some debug messages from the driver on the debug output
serial port, but so far, nothing. Any ideas please?

Best Regards
--
Phil

Remove the nospam section from my e-mail address.


"Bruce Eitman [eMVP]" wrote:

That is fine, just wanted to make sure that was what you were talking
about
and not that you were refering to something else.

That should work, so now the question is why not.

--
Bruce Eitman (eMVP)
Senior Engineer
beitman AT applieddata DOT net

Applied Data Systems
www.applieddata.net
An ISO 9001:2000 Registered Company
Microsoft WEP Gold-level Member

"Phil" <pclaydon@xxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:762526C7-6AE6-4C05-AC18-41AE2C15C844@xxxxxxxxxxxxxxxx
A subproject as shown in the Visual Studio 2005/Platform Builder 6.0
Solution
Explorer:-) What is a userproject? a term from an earlier version of CE
perhaps?
--
Phil

Remove the nospam section from my e-mail address.


"Bruce Eitman [eMVP]" wrote:

Phil:

What do you mean by subproject? During makeimg,
public\common\oak\misc\premakeimg.bat runs and creates
PBUserProjects.bib
which should include the bib files from the user projects.

I suspect that you either don't mean the same thing by subprojects as
PB
does, or your subproject isn't setup correctly for bib files, like it
is
for
reg files.


--
Bruce Eitman (eMVP)
Senior Engineer
beitman AT applieddata DOT net

Applied Data Systems
www.applieddata.net
An ISO 9001:2000 Registered Company
Microsoft WEP Gold-level Member








.

Relevant Pages

  • Re: Hive based Registry Booting time
    ... Do you have any debug output? ... Are the hives actually there after it boots? ... beitman AT applieddata DOT net ... My platform is working fine with ram based registry. ...
    (microsoft.public.windowsce.platbuilder)
  • Re: Incorporating a 3rd party driver into a BSP/Image
    ... because my IT department is paranoid about what they let us install. ... You may want to look for a tool to get the registry out of the CAB file. ... beitman AT applieddata DOT net ... driver suite actually run as if a CAB had installed it. ...
    (microsoft.public.windowsce.platbuilder)
  • Re: FlashROM as a disk in CE 5.0
    ... beitman AT applieddata DOT net ... Applied Data Systems ... Microsoft WEP Gold-level Member ... I have added the Registry settings to Project.reg file like ...
    (microsoft.public.windowsce.platbuilder)
  • Re: Deleting a registry key in Win CE 6.0 (.net)
    ... Bruce Eitman (eMVP) ... beitman AT applieddata DOT net ... An ISO 9001:2000 Registered Company ... Set up the system to persist the registry on a timed bases. ...
    (microsoft.public.windowsce.embedded)
  • Re: TaskBar under CE.NET
    ... > Your registry fix works perfectly using DWORD. ... > "Bruce Eitman " wrote: ... >> beitman AT applieddata DOT net ... >> Applied Data Systems ...
    (microsoft.public.windowsce.embedded.vc)
Loading