Re: Display problem! cant set 16bpp...

Tech Tip: Click here to run a free scan for Windows Errors and optimize PC performance

I m running the nk.bin files from bios loader. I mean i am sysgen ing the
image os and then i am copying nk.bin file to DiskOnModule and Start the
device.
Do you think that i have still a way to dump registry while opening image in
this way and connect with plat.builder or with any remote tool after winCE
started? It would be very nice.
Do you know a registry editor s/w that runs on winCE?
And you may be right about memory configuration cause i have changed smt. on
config.bib and oeminit.asm. Can you explain the memory configuration effect
on display?
Thanks...


"Voidcoder" <voidcoder@xxxxxxxxx>, haber iletisinde sunlari
yazdi:%23oaYIzlIGHA.2668@xxxxxxxxxxxxxxxxxxxxxxx
> Hm, I'm very confused now :) If you can't download
> your own image, how do you see VGA problems
> on your own builds?
>
> What I mean is to dump registry when !their! precompiled
> image is running, not yours. I'm sure it should be a way to
> setup a Platman connection to device via ethernet, serial,
> rndis, ActiveSync or whatever.
>
> Once you get the copy of registry from their build, you could
> try to compare registry settings for display driver. In case the
> driver binaries are identical (it is possible that the driver
> binary in the precopiled image is different form one you have
> in your current BSP), it is possible that some external settings
> affect the driver's behaviour. Probably registry settings, or may
> be different memory configuration in your config.bib.
>
>
>
> "CAGRI" <arge5@xxxxxxxxxxxx> wrote in message
> news:%233KUealIGHA.3984@xxxxxxxxxxxxxxxxxxxxxxx
>> Unfortunately I couldnt achieve to download image from PlatBuilder and i
>> have tried someone from icop support but he is not writing with me he is
>> just referancing to some sheets of Step by Step guide that i have read 50
>> times.
>> Thanks anyway any other idea? Do you think it should definetly be solved
>> by registery? Whant does it mean to you its telling same "VGAMode: X:800,
>> Y:600 ,Bpp:16, Refresh Rate:60"
>> debug message but not correct bpp?
>>
>>
>>
>>
>>
>> "Voidcoder" <voidcoder@xxxxxxxxx>, haber iletisinde sunlari
>> yazdi:ezHLbGlIGHA.2628@xxxxxxxxxxxxxxxxxxxxxxx
>>> Is there any way to setup a "Platform Manager Connection"
>>> with the target when running on the prebuilt image?
>>> Are you able to get eVC++ or Remote Tools connected
>>> to the target? In that case just go to Tools menu in PB or
>>> eVC and run Remote Registry Editor. Connect the tool
>>> to device and export the registry to PC.
>>>
>>> Otherwise (no way to run Remote Tools), you are about
>>> to run your own app to enum registry entries, or try
>>> to find a third-party registry editor for CE.
>>>
>>> Have you tried to contact ICOP support?
>>>
>>> "CAGRI" <arge5@xxxxxxxxxxxx> wrote in message
>>> news:Oqey55kIGHA.2212@xxxxxxxxxxxxxxxxxxxxxxx
>>>> Hi,
>>>> Thanks for answer. In fact i dont know hot to dump registry. Could you
>>>> please explain?
>>>>
>>>> "Voidcoder" <voidcoder@xxxxxxxxx>, haber iletisinde sunlari
>>>> yazdi:eVDmC2kIGHA.668@xxxxxxxxxxxxxxxxxxxxxxx
>>>>> Try to dump registry on prebuilt image and
>>>>> compare vs. your platform.reg (or better reinit.ini).
>>>>> See if there are some differences for the
>>>>> AFD, PPP and display drivers.
>>>>>
>>>>>
>>>>>
>>>>> "CAGRI" <arge5@xxxxxxxxxxxx> wrote in message
>>>>> news:OliUlfkIGHA.216@xxxxxxxxxxxxxxxxxxxxxxx
>>>>>> Hi,
>>>>>> I got ICOP Vortex86 6071 board and winCE 5.0 plat builder and using
>>>>>> AUO 12.1 inch (800x600 tft lcd) panel.
>>>>>> When i m using the pre-built image that i downloaded from icop's web
>>>>>> site, the display is very well. I m following serial debug outbut
>>>>>> from hyperterminal and it says:
>>>>>> "
>>>>>> VGAMode: ModeID:47, ModeIndex:1, RateIndex=2
>>>>>> VGAMode: X:800, Y:600 ,Bpp:16, Refresh Rate:60
>>>>>> "
>>>>>>
>>>>>> So I have built the image as following instructions in Step by Step
>>>>>> or Starter Guide like manuals by writing propriate registery entries
>>>>>> for 800x600x16 VSync:60Hz.When i load the image(by biosloader) the
>>>>>> debug output :
>>>>>>
>>>>>> "
>>>>>> SysInit: Mapping Extra RAM from 0x84000000 to 0x87000000
>>>>>> GDTBase=817b50e8 IDTBase=817d6860 KData=817dd800
>>>>>> Windows CE Kernel for i486 Built on Jun 24 2004 at 18:23:42
>>>>>> g_pPageDir = 817e0000 X86Init done, OEMAddressTable = 817e1000.
>>>>>> DeviceFolder::LoadDevice!Enumerate Found deprecated load
>>>>>> instructions at (Driver
>>>>>> s\BuiltIn\AFD). Driver cannot be unloaded.
>>>>>> DeviceFolder::LoadDevice!Enumerate Found deprecated load
>>>>>> instructions at (Drivers\BuiltIn\PPP). Driver cannot be unloaded.
>>>>>> CalibrateStallCounter: delay is 62
>>>>>> Get Mode info from /L Args->VideoMode=0!! cx=800, cy=600!!
>>>>>> VGAMode:
>>>>>> ModeID:47,
>>>>>> ModeIndex:1, RateIndex=2
>>>>>> VGAMode: X:800, Y:600 ,Bpp:16, Refresh
>>>>>> Rate:60
>>>>>> SYSAGP:Reserved memory use registry
>>>>>> setting!!
>>>>>> Address:80220000 Size:00300000
>>>>>> Lyg.p: Layout Manager
>>>>>> successfully initialized to 1
>>>>>> Explorer(V2.0) taskbar thread started.
>>>>>> NDISPWR:: Found adapter [PCI\RTL81391]
>>>>>> "
>>>>>> I can see:
>>>>>> VGAMode: X:800, Y:600 ,Bpp:16, Refresh Rate:60
>>>>>> in my image too. Although the resolution seems ok on screen, the
>>>>>> color depth is not! It seems like 8bpp instead of 16bpp.
>>>>>> I also couldnt figure out "Driver cannot be unloaded" messages.
>>>>>> What could be the display's ploblem and what it means that messages?
>>>>>> Any comment would be nice,
>>>>>> Thanks in advance...
>>>>>> -CAGRI-
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>


.

Quantcast