Re: PB 5.0 Target Device connectivity problem

Tech Tip: Click here to run a free scan for Windows Errors and optimize PC performance

Thanks for having a look on my problem.

The development board sends correctly all BOOTME frames.
I have check it with an IP sniffer tool (Ethereal) to be sure that frame are
correctly received on my PC.
The frame is an broadcast UDP frame.
source port :980
dest port :980

I have also noticed some errors from CESVCHOSTlogged in my PC events
observer:
>> Process Id: 204
>> Thread Id: 1720
>> Zone: CoreCon_Error_SvcHost
>> Source Code: e:\pbmac\corecon\src\svchost\exe\svchost_impl.cpp(759)@CSvcHost_Impl::GetService
>> Failed to get a service. hr=800401f3

Jean-François


"Travis Hobrla [MS]" wrote:

> Can you connect a serial cable to see if the device is actually sending
> BOOTMEs over the network?
>
> "JF Beaumier" <JFBeaumier@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
> news:D5271580-F738-4B69-83D4-8782DDB22C38@xxxxxxxxxxxxxxxx
> > The identified firewall (F-Secure) has been deactivated, so no firewall
> > should be present.
> >
> > JF
> >
> > "Dean Ramsier" wrote:
> >
> >> Firewall?
> >>
> >> --
> >> Dean Ramsier - eMVP
> >> BSQUARE Corporation
> >>
> >>
> >> "JF Beaumier" <JFBeaumier@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
> >> news:FB25ABBE-F0C7-4431-BFE8-AB19D4F95451@xxxxxxxxxxxxxxxx
> >> > Thanks for helping me.
> >> >
> >> > When I open the menu "Target / Connectivity option.." , press the
> >> > download
> >> > (ethernet) settings button and start the development card, it shoulb be
> >> > detected by PB. It has been correctly detected once but is not
> >> > reconised
> >> > any
> >> > more.
> >> > I was using the same development card on a previous PC and it was ok,
> >> > but
> >> > I
> >> > change my PC recently and have this problem since.
> >> >
> >> > The problem seems to be around the process "cesvchost" which does not
> >> > receive the "boot me" UDP frame from the development card.
> >> >
> >> > JF
> >> >
> >> > "Paul" wrote:
> >> >
> >> >> We use the SMDK2410 sucessfully. What do you mean by PB does not
> >> >> detect
> >> >> the
> >> >> target any more? Do you reset dev board and do Target Attach device.
> >> >> At
> >> >> which point does it not do what you wish it to do.
> >> >>
> >> >> Paul
> >> >>
> >> >> "JF Beaumier" <JF Beaumier@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
> >> >> news:5792BC38-44BA-44C4-8448-019DDC5A5E57@xxxxxxxxxxxxxxxx
> >> >> > Can anybody have a look of this strange behaviour?
> >> >> >
> >> >> > I have installed PlatformBuilder CE 5.0 on Windows XP SP1
> >> >> > I have a Samsung development board SMDK2410 with an eboot working
> >> >> properly.
> >> >> >
> >> >> > I have set the target device connectivity options to:
> >> >> > Download : Ethernet
> >> >> > Transport : Ethernet
> >> >> > Debugger : Kdstub
> >> >> >
> >> >> > I have been able to build a software and download it properly on my
> >> >> target,
> >> >> > but after another build, PB does not detect the target any more.
> >> >> >
> >> >> > JF Beaumier
> >> >> >
> >> >>
> >> >>
> >> >>
> >>
> >>
> >>
>
>
>
.

Quantcast