Re: AT91RM9200EK Image downloading not possible

Maybe you should check your connectivity options in Platform Builder
(target->connectivity options->core service settings) and make sure PB will
try to download the image (set to always)
HTH

--
----------------------------------------------------------------
Anthony Pellerin
ADENEO (ADESET)
Windows Embedded Consultant
<apellerin AT adeneo DOT adetelgroup DOT com>
http://www.adeneo.adetelgroup.com
Tél : +33 (0)4.72.18.57.77
Fax : +33 (0)4.72.18.57.78
----------------------------------------------------------------


"Arcturus" <noreply> wrote in message
news:435659f3$0$27856$afc38c87@xxxxxxxxxxxxxxxxxx
>
> Hi,
>
> I'm not able to download the image on the AT91RM9200EK: the board reboots
> just before the tranfer starts as described in next trace:
>
>
> ATMEL LOADER VER 1.02 Jul 20 2004 17:10:43
> *--------------------------------------*
> DataFlash:AT45DB642
> Nb pages: 8192
> Page Size: 1056
> Size= 8650752 bytes
> Logical address: 0xC0000000
> *--------------------------------------*
> 1: Download Dataflash [addr]
> 2: Read Dataflash [addr]
> 3: Start BOOT [C0004000 => 20000000]
> *--------------------------------------*
> Enter: Load CE-BOOT from dataflash[c0004000] to SDRAM[20000000]
> Set PLLA to 180Mhz and Master clock to 60Mhz and start EBOOTþInit Debug
> Serial OK!
>
> Microsoft Windows CE Ethernet Bootloader Common Library Version 1.1 Built
> Nov 24 2004 10:12:18
> Microsoft Windows CE Ethernet Bootloader 1.0 for AT91RM9200EK board (May
> 23 2005 : 11:17:55)
> Copyright (c) 2001 Microsoft Corporation
> Portions copyright (c) 2004 Adeset SAS - Atmel Corporation
> Integration and development performed by Adeset SAS
>
> Bus Speed 59897 kHz
> CPU Speed 179692 kHz
>
>
> Performing POST...Successful
> Nand Density = 0x38 Device sdf status=0xBC
>
> Nand Density = 0x38 Device sdf status=0xBC
>
> Nand Density = 0x38 Device sdf status=0xBC
>
> Nand Density = 0x38 Device sdf status=0xBC
>
> RAW_Init : Initialisation Done ...
>
>
>
> Press any key to break into configuration menu 5 ...
> Press any key to break into configuration menu 4 ...
> Press any key to break into configuration menu 3 ...
> Press any key to break into configuration menu 2 ...
> Press any key to break into configuration menu 1 ...
>
> g_BldrSettings.nFlags =1.
> Boot Args @ 0x20048800
> +EDBG:AT91Init
> EDBG:AT91Init low level init for bootloader
> ***AT91_net: set MII for 100BaseTX and Full Duplex
> ***Basic Emac Init : ethernet at 0xFFFBC000 Base100-Full
> (hwaddr = DE:DE:03:02:01:00)
> EDBG:AT91Init using I/O range at 0xFFFBC000
> AT91_EmacReadPhy n°1! OK
> AT91_EmacReadPhy n°2! OK
> EDBG:AT91Init Reading MAC address 0x00000100 0x00000302 0x0000DEDE
> -EDBG:AT91Init
> INFO: Debug Ethernet MAC Address:00:01:02:03:DE:DE
> System ready!
> Preparing for download...
> CreateDeviceName
> UpperDWORD = 0x00000102
> INFO: Using device name: 'AT91EK57054'
> InitDHCP():: Calling ProcessDHCP()
> ProcessDHCP()::DHCP_INIT
> Got Response from DHCP server, IP address: 192.168.0.212
>
> ProcessDHCP()::DHCP IP Address Resolved as 192.168.0.212, netmask:
> 255.255.255.0
> Lease time: 86400 seconds
> Got Response from DHCP server, IP address: 192.168.0.212
> No ARP response in 2 seconds, assuming ownership of 192.168.0.212
> +EbootSendBootmeAndWaitForTftp
> Sent BOOTME to 255.255.255.255
> Got EDBG_CMD_JUMPIMG
> Got EDBG_CMD_CONFIG, flags:0x00000000
> -EbootSendBootmeAndWaitForTftp
> g_BldrSettings.nFlags 1
> SpinForever...
>
> -I- AT91F_LowLevelInit(): Debug channel initialized
> ESC[2J
>
>
> Thanks for your help.
>


.

Relevant Pages

  • Re: USB Active sync problem
    ... Windows Embedded Consultant ... <apellerin AT adeneo DOT adetelgroup DOT com>http://www.adeneo.adetelgroup..com ... [NOTIFY] ... Configuration,Minimal GWES configuration, Minimal Input ...
    (microsoft.public.windowsce.platbuilder)
  • Re: Internet Explorer Ignoring supportedRuntime Directive
    ... even if you specify a different value in the application configuration ... Native image will not be probed in LoadFrom context. ... LOG: Attempting download of new URL http://navilinkd2/assemblies/Main.dll. ... The web server may be configured to ...
    (microsoft.public.dotnet.framework.clr)
  • Re: Downloading Nk.bin from Eboot through USB
    ... <apellerin AT adeneo DOT adetelgroup DOT com>http://www.adeneo.adetelgroup.com ... On Mar 8, 6:01 pm, "Anthony Pellerin" ... What are the steps i have to follow if i have to download myNk.bin ... I checked with DNW utility provided my Samsung. ...
    (microsoft.public.windowsce.embedded)
  • ANN: matplotlib-0.91.2 - a python graphics package
    ... A new release of matplotlib is posted to the sourceforge download ... better configuration - Darren Dale has provided support for a site.cfg ... record array support - New functions for loading, ...
    (comp.lang.python)
  • Re: AT91RM9200EK Image downloading not possible
    ... >> I'm not able to download the image on the AT91RM9200EK: ... >> Press any key to break into configuration menu 5 ... ... >> Got Response from DHCP server, ...
    (microsoft.public.windowsce.platbuilder)