Re: SMI Lynx display driver?
From: Maverick (maverick_at_newsfan.net)
Date: 02/18/04
- Next message: Maxim S. Shatskih: "Re: NDIS IM [Passthru]: ProtocolReceivePacket not called in device!"
- Previous message: street_ken: "4bpp LCD display problem?"
- Maybe in reply to: Maverick: "SMI Lynx display driver?"
- Messages sorted by: [ date ] [ thread ]
Date: Wed, 18 Feb 2004 13:37:08 +0800
peterpan ,
Thank you for your driver. For your question, you may try this:
1、Try to install some other OS, say MS-DOS, on your HDD to see if they can
boot. If not, the HDD or the cable is bad.
2、Change the a new HDD. I heard that the ATAPI driver in PB is not written
very well, and it doesn't support some kind of HDD. Or you can try to find
some better ATAPI driver on the Internet.
maverick
"peterpan" <pan222@163.com> 写入邮件
news:%233a2U2d9DHA.1472@TK2MSFTNGP11.phx.gbl...
> maverick
>
> The attached file is the driver of 712 they sent to me.
>
> My CF is a IDE device(the second master) not a usb device(there is a
CF
> sloto on my SDB). The HD’s volume is 8GB. I just fdisk 1GB ( FAT16) .
>
> I have seen the other people ‘s Image can boot both from the
harddisk
> and CF card and can manage the other harddisk ( harddisk & harddisk2) in
my
> computer when the wince works.
>
> Now I have found another problem.
>
> If I install wince OS in that harddisk only and boot from it without CF
card
> on board, my CE can't boot either.
> other phenomena are the same.
>
>
>
>
> "Maverick" <maverick@newsfan.net> 写入邮件
> news:%23u05J%23Q9DHA.1816@TK2MSFTNGP12.phx.gbl...
> > Thank you peterpan. I mailed to Silicon Motion last week but got nothing
> > yet. Would you please mail me a copy of that? Thx
> >
> > Your problem is very common. INVALID devices include unsupported USB
> > devices, Large Volumn IDE devices, etc. So I think maybe your problem is
> > caused by your HD's volumn. If it's too large, CE cannot drive it. I
have
> > tried a 40G HD, it works.
> >
> >
> > "peterpan" <pan222@163.com> 写入邮件
> > news:OQ$URPt8DHA.2416@TK2MSFTNGP10.phx.gbl...
> > > hi,Maverick
> > > you could mailthis address support@siliconmotion.com. I have got
the
> > > driver of smi712's for ce4.1 from them, but their driver has a bug
which
> > it
> > > only support 60Hz's refresh rate and you can't change it by modifying
> the
> > > platform.reg 's display key.
> > > I have meet a problem as follows: did anybody meet the similar
> problem
> > ?
> > > My CE platform is based on geode's bsp(cpu is ns cs5530) with a
> > > HDD(3.5", FAT16) and one SanDisk(64M). When I turn on the power with
> only
> > > SanDisk connected to IDE (via a daughter board), it runs perfect. But
if
> I
> > > connected both Hdd and SanDisk to IDE, the system can start and load
OS
> to
> > > DRAM. But it can't show the "Desktop" screen. The detailed condition
is
> as
> > > below:
> > >
> > > 1. System Power On, 1 beep.
> > > 2. BIOS detects 2 IDE devices (Fujitsu HDD as C, SanDisk CF as D)
> > > automatically.
> > > 3. System boots from SanDisk and WinCE logo shows on the LCD panel.
> > > 4. When the progress bar goes 100%, the WinCE logo disappear.
> > > 5. The hard disk Read/Write indication LED lights up always, and the
> > system
> > > stops here.
> > >
> > > what's wrong with it? I have edit the geodeide.reg file to uncomment
the
> > > line for slave device
> > > .Hdd is the first master and the cf is the second master on my
platform
> > >
> > >
> > > "Mike Engel" <andi@reterioja.com> 写入邮件
> > > news:%23Igz0qh8DHA.2064@TK2MSFTNGP11.phx.gbl...
> > > > Non of the PB display driver will work. There is a Lynx driver
> available
> > > for
> > > > Windows CE. Have you tried it on the SMI web side? If not search on
> the
> > > web
> > > > and you will find some you has the driver.
> > > >
> > > > Best regards,
> > > >
> > > > Mike Engel
> > > >
> > > > "Maverick" <maverick@newsfan.net> escribi?en el mensaje
> > > > news:#ElcMcg8DHA.3704@tk2msftngp13.phx.gbl...
> > > > > Hi, all
> > > > >
> > > > > I am using a board which has a SMI Lynx 712 display chipset on it.
I
> > had
> > > > > tried including all the display drivers provided by platform
> builder.
> > > But
> > > > > each time I failed to light the screen. Does anyone know where to
> get
> > > > such
> > > > > a driver for CE.net 4.0? Or is there any compatible driver for
this
> > kind
> > > > > display chipset?
> > > > >
> > > > > regards
> > > > >
> > > > > maverick
> > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>
>
- Next message: Maxim S. Shatskih: "Re: NDIS IM [Passthru]: ProtocolReceivePacket not called in device!"
- Previous message: street_ken: "4bpp LCD display problem?"
- Maybe in reply to: Maverick: "SMI Lynx display driver?"
- Messages sorted by: [ date ] [ thread ]
Relevant Pages
|
