Re: RTL 8139D Lan card using in Windows CE 5.0

Ok, so what is going wrong? It seems the ethernet chip is initializing properly, using static IP 192.168.10.182 and is now sending BOOTME's to the network. You now have to go to Platform Builder, load your OS Design, then click menu Target, choose Connectivity options and configure your connection to use ethernet as transport and KdStub as debugger. Now click the "Configure" button and choose CEPC9279.

Of course your dev pc has to be in the 192.168.10.xxx network with a subnetmask of 255.255.255.0 to receive the BOOTME's.

I think you should read up on how to work with platform builder a bit more...


Good luck,

Michel Verhagen, eMVP
Check out my blog: http://GuruCE.com/blog

GuruCE Ltd.
Microsoft Embedded Partner
http://GuruCE.com
Consultancy, training and development services.

ashsantu@xxxxxxxxx wrote:
Hello
Thanks for the reply.

When im was tried to download the image Following Debug message shown
On Serial hyper terminal
//
Microsoft Windows CE Ethernet Bootloader Common Library Version 1.0
Built Apr
11
2003 20:28:06
Microsoft Windows CE Ethernet Bootloader 3.4 for CE/PC (Apr 22
2003)
Boot Args @ 0x2CA56 and ucLoaderFlags is
1
FlashInit
FMD_Init
-FlashInit:Fails!!!!
PCI Device Configurations (1 PCI bus(es)
present)...
========================================================
Bus, Device, Function = 0, 10, 0
Vendor ID, Device ID = 0x126F,
0x0712
Base Class, Subclass = 3, 0 =>
DISPLAY_CTLR
Interrupt = 11
BaseAddress[0] = 0xFD000000
(Memory)
========================================================
Bus, Device, Function = 0, 12, 0
Vendor ID, Device ID = 0x10EC,
0x8139
Base Class, Subclass = 2, 0 =>
NETWORK_CTLR
Interrupt = 10
BaseAddress[0] = 0x1000 (I/
O)
BaseAddress[1] = 0xFC001000
(Memory)
========================================================
Bus, Device, Function = 0, 19, 0
Vendor ID, Device ID = 0x0E11,
0xA0F8
Base Class, Subclass = 12, 3 =>
SERIAL_BUS_CTLR
Interrupt = 11
BaseAddress[0] = 0xFC000000
(Memory)
========================================================
FindAllPCINetCard: Searching for PCI Ethernet
NIC ...
FindALLPCINetCard(0): Found Ethernet NIC (IRQ=10, IOBase=0x1001,
Type=4).
FindPCINetCard:Argument IOBASE=0,
IRQ=0,TYPE=2
FindPCINetCard:Found 1 PCI Ethernet
NIC ...
FindPCINetCard: Found Ethernet NIC (IRQ=10,
IOBase=0x1000).
RTL8139InitDMABuffer():: Start[0x200000]-[0x200000] -
Size[0x20000]
Tx[0x200000] - Rx[0x201800] -
RxLength[0
RTL8139Init():: BaseIO[0x1000] :
MemOffset[0x1]
RTL8139Init():: TxBuff[0x200000] - RxBuff[0x201800] -
LastRx[0x2117FF]
RTL8139Init:: MAC =
00-18-4D-6F-24-3F
RTL8139 ethdbg library:
AutoNegotiate..
RTL8139:: RTL8139HWSetMCRegs():: Set all to
0x00
Returned MAC Address:00:18:4D:6F:
24:3F
System ready!
Preparing for download...
OEMPreDownload ucLoaderFlags is 0
Using device name: CEPC9279
Using static IP address: B60AA8C0
+EbootSendBootmeAndWaitForTftp
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255
RTL8139:: RTL8139HWSetMCRegs():: Set all to 0x00
+RTL8139EnableInts()..
-RTL8139EnableInts()..
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255
/////////////////////////////////////////////////////////////////////////////////

board manufacturer: ZFmicro x86 board
BSP used - CEPC BSP
Wince 5.0 Version.
.