Re: ports

Tech-Archive recommends: Fix windows errors by optimizing your registry

You can define one port per interface. Install extra interfaces and change
the port number on each as required. You can also assign multiple protocols
and so the same think so you can use RDP and Citrix Protocol. That will
give you two ports per interface. Beyond that you can do no more.


--
Jim Vierra
http://msdn.microsoft.com/theshow/Episode048/default.asp
"Patrick Rouse" <PatrickRouse@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:F34B369C-EA75-4D15-8F24-4752FDFF9C98@xxxxxxxxxxxxxxxx
>I don't believe this is possible. Please explain why you require this.
>
> "Sathish Kumar Nair" wrote:
>
>> Sir,
>>
>> As per Link the Mentioned below we can able to change the port from 3389
>> to
>> any other port number. But i require to configure the terminal service to
>> use
>> multiple ports . for example at present terminal service is using 3389,
>> by
>> editing the registry we can change to other port like 3900 .
>>
>> I require to configure the terminal service to use multiple port like
>> 3389,3390,3391,3392,3393,3394,3395 like this
>>
>> waiting for your reply
>>
>> regards
>> sathish Kumar nair
>> "Patrick Rouse" wrote:
>>
>> > You might be able to setup multiple RDP-Tcp connections (in tscc.msc)
>> > then
>> > bind each to a different port number in the registry:
>> >
>> > http://support.microsoft.com/default.aspx?scid=kb;en-us;q187623
>> >
>> >
>> >
>> > "Sathish Kumar Nair" wrote:
>> >
>> > > How to configure Terminal Service to use multiple port for remote
>> > > desktop
>> > > administration
>> > >
>> > > For example , At Present Terminal Service uses port 3389, but i want
>> > > to
>> > > configure
>> > >
>> > > Terminal service to use port ranging from port 3389 - 3400
>> > >
>> > > waiting for your reply
>> > >
>> > > Regards
>> > > sathish kumar Nair
>> > >


.

Relevant Pages

  • Re: change ISA IP address
    ... You can have multiple IP's on the external interface for web-publishing ... can re-use the same listener for all your web publishing ... >> port 80, as WPAD in DNS does NOT allow specifying a custom port like WPAD ...
    (microsoft.public.isa)
  • Re: Additional Hardware Module with Xilinx MicroBlaze Processor
    ... a pcore for your LCD module. ... You can write to the fsl interface with the function putfslx, ... What I would like to do is define a GPIO port on the processor to ... and write to the FSL bus suffice? ...
    (comp.arch.fpga)
  • ng_one2many v.s. AFT (NIC Fault Tolerance/Fail Over/Redundancy Revisited)
    ... Then I was thinking about the OpenBSD/NetBSD bridgeinterface. ... Spanning Tree as an alogirth could provide Intel AFT ... illustrates, regardless of which interface is the root port, ARP replys ... Topology change flag not set, detected flag not set, changes 54 ...
    (freebsd-questions)
  • Re: ng_one2many v.s. AFT (NIC Fault Tolerance/Fail Over/Redundancy Revisited)
    ... Then I was thinking about the OpenBSD/NetBSD bridgeinterface. ... Spanning Tree as an alogirth could provide Intel AFT ... illustrates, regardless of which interface is the root port, ARP replys ... Topology change flag not set, detected flag not set, changes 54 ...
    (freebsd-questions)
  • Newest Stack-180 CP/M system with motherboard option and networking
    ... CPU and includes 1 meg of ram and one serial port for terminal I/O The ... GIDE board has two IDE ports called Primary and Secondary which allow ... It is a ATX type motherboard that these ... and another IDE interface. ...
    (comp.os.cpm)