Re: Windows Server 2008 remote desktop using computer name setup

Tech-Archive recommends: Speed Up your PC by fixing your registry

The time clock is the device that employees use to clock in and clock out. It
is on the network. I found the router had the MAC address so I was able to
make a DHCP reservation.

I did check 13 of the 14 computers on that segment using ipconfig /all and
the DNS server is the server local IP address. No Public IP addresses are
present on the computers.

I am ready to close this thread. Can not say the answer for either problem
(Can't remote using computer name and excessive log on time) is here. You
don't feel the changes I made should have fixed either problem yet neither
problem currently exists.

Server setup progress has been made since the DHCP service has been switched
over from router to the server.

"Lanwench [MVP - Exchange]" wrote:

techcoor <techcoor@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
I did wait a couple nights before staying late to switch over the DHCP
service from the router to the Server and setting up reservations for
the IP Phones, network printers (can not find where the time clock
MAC is)

What do you mean by time clock?

Again the changes I make seem to fix the problem I have even though
you said No. One computer (auto DNS) that was slow now logs normally
and the static IP computer with the DNS pointed to the server also
logs normally.

And you've confirmed that there are no public IPs in any workstation's
ipconfig /all ? This is critical. You may get things to appear functional
without that, but you will absolutely have problems at some point.

The next step would be the setup of the network printers and the print
servers. However, I assume I should start a new thread.

Yes, I would recommend that.

Thanks for the help.



"Lanwench [MVP - Exchange]" wrote:

techcoor <techcoor@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
The problem I posted was apparently caused by the DNS reverse lookup
referring to the wrong subnet 192.168.0.x when it should have been
192.168.1.x. That has been fixed.

Cool, but note that this can't be your problem. An incorrect reverse
lookup entry won't cause you problems with a forward lookup.

What problems are caused by the DHCP settings. Could this be the
problem of slow logon on specific computers that was patched by
setting the DNS to point to the server? (It took 8 minutes to log on
to one computer with a static IP address)

No; the problem is that you've got DNS server IPs listed in your
clients that are not internal/AD-integrated DNS servers. The reason
for having Windows handle DHCP is that it makes dynamic DNS updates
work more reliably.

I am not sure what you mean by DHCP reservations. Are you talking
about excluding address such as the static IP address for the
printers?

No; I don't use static IP addresses for printers. I set up DHCP
reservations for printers (specific MAC addresses always get the
same IP issued via DHCP, so I don't have to keep a list of statics).
I use statics only for servers & network equipment.

"Lanwench [MVP - Exchange]" wrote:

techcoor <techcoor@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
My first question would be how do I gracefully switch the DHCP
server?

This does sound like an after hours job because the computer users
would probably lose their Internet connections when the switch
over occurs.

I assume the procedure would go something like this:
On the server add the DHCP server
http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/

Disable the DHCP server on the router

Go to each computer and do a ipconfig /release then ipeconfig
/return

ipconfig /release & ipconfig /renew, yes.

Sounds like you've got it. If you've got any DHCP reservations make
sure you preconfigure those on the Windows box too, before making
the switch.

"Lanwench [MVP - Exchange]" wrote:

techcoor <techcoor@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
Yes, there is active directory.

The Windows XP computers for DNS are set up to point to the
router.

This is a problem. They must point only to the LAN IP of your
internal DNS server. No public IPs, no router. Your router should
not be doing DHCP either.

The router for DNS is pointed to the static IP of the server. I
have to check the DNS settings of the server.

See above :-)

"Lanwench [MVP - Exchange]" wrote:

techcoor <techcoor@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
If I set up Windows XP computers for remote desktop, go to the
remote computer, used ipconfig to find the IP address, then
use remote desktop and the IP, I can use remote desktop to
reach the remote computer.

If I try the computer name then the remote desktop will not
find the computer.

How do I set up Windows Server 2008 so I can use the remote
desktop with a computer name.?

Are you using AD? If so, all your workstations & servers should
specify only the internal DNS server IP(s), no public IPs. In
fact, without AD you can still do that, and it's often a good
idea. You configure the DNS server itself with forwarders to
your ISP's DNS servers for external resolution.




.

Relevant Pages

  • Re: SBS 2003 Misconfigured?
    ... I've thrown quite a bit at them, and just have to disagree that they are inherently less secure than the netgear. ... setup DHCP and I have also gone in and manually created a new scope ... when I first used the Netgear router with SBS 2003, ... than one SBS server in a company makes no sense. ...
    (microsoft.public.windows.server.sbs)
  • Re: SBS 2003 Misconfigured?
    ... Yeah, maybe it's not that different from the Netgear, for all that. ... that when I first used the Netgear router with SBS 2003, ... tech spend 4+ hours on my system, and then tell me to enable DHCP ... more than one SBS server in a company makes no sense. ...
    (microsoft.public.windows.server.sbs)
  • Re: How do I configure SBS 2003 as a DHCP server?
    ... To disable the private "LAN" side DHCP service (not the DHCP service on the ... of the PPPoE adapter and enable your Speedstream as a DSL modem and router. ... For the Vista computer to interact with SBS, ... Windows Small Business Server 2003: ...
    (microsoft.public.windows.server.sbs)
  • Re: Urgent! New router and big disaster
    ... OK, yes, I've struck a router which would only allow DHCP clients access to ... no internet connection from the server. ...
    (microsoft.public.windows.server.sbs)
  • Re: SBS 2003 Misconfigured?
    ... setup DHCP and I have also gone in and manually created a new scope ... when I first used the Netgear router with SBS 2003, ... one SBS server in a company makes no sense. ...
    (microsoft.public.windows.server.sbs)