Re: Connect a Wireless Router to my SBS Network

I assume your DSL modem-router is acting as a router (with a WAN and a LAN
side) and not as a bridge (simply passing all traffic into the network). If
it's acting as a router, the WAN IP address assigned by your ISP should be
set on the WAN side of the DSL modem-router.

--
Merv Porter [SBS-MVP]
============================

"SBS Golfer" <Mr.Bogus@xxxxxxxxxxxxxxx> wrote in message
news:uazjN2qPJHA.1164@xxxxxxxxxxxxxxxxxxxxxxx
that is correct and sffirmitive. I'm puzzled though as to how the wireless
resolves DNS requests? Shouldn't my WAN settings reflect my ISP's
settings? In other words for the WAN IP, Gateway, mask and dns?


"Merv Porter [SBS-MVP]" <mwport@xxxxxxxxxxxxxxxxxxx> wrote in message
news:eflkGuqPJHA.1908@xxxxxxxxxxxxxxxxxxxxxxx
Also, you should have the cable that comes from the DSL modem-router
plugged into the WAN port of the Airlink router (not one of the 4
available LAN ports).

--
Merv Porter [SBS-MVP]
============================


"SBS Golfer" <Mr.Bogus@xxxxxxxxxxxxxxx> wrote in message
news:%23AX%23mfqPJHA.4008@xxxxxxxxxxxxxxxxxxxxxxx
Hey Merv,
OK so I think i'm almost there again. Followed your suggestions.

This setup is the Airlink wireless attached to the 5-port switch? YES

Assumption: the DSL router-modem is 192.168.1.1

If so, try this...

LAN IP Address: 192.168.2.1
Static IP Address: 192.168.1.2
Static Subnet Mask: 255.255.255.0
Static Gateway: 192.168.1.1
Primary DNS: 192.168.1.1
Secondary DNS: 192.168.1.1

Changed my laptop IP to 192.168.2.10 and the wireless to 192.168.2.1.and
am able to connect directly to the wireless. Deleted to old network.
Created a new one and changed channels. Select WPA-PSK

So now I am ble to connect to the AirLink wireless router either
directly with a cable or I'm also able to get to the administration page
via 192.168.2.1 via wireless. Checked my laptop IP settings and I am
getting

Dynamic IP 192.168.2.109
Subnet Mask 255.255.255.0
Gateway 192.168.2.1

So all looks good. Only problem is I can't get to the internet. Any
ideas? I've got no firewalls running. My Internet/Connections/LAN
Settings is set to "Automatically detect settings".




"Merv Porter [SBS-MVP]" <mwport@xxxxxxxxxxxxxxxxxxx> wrote in message
news:eK8KD6gPJHA.2348@xxxxxxxxxxxxxxxxxxxxxxx
Are you using WPA-RADIUS authentication on the wireless router? Should
be WPA-PSK.

Also, what is the model number of the Airlink router?

--
Merv Porter [SBS-MVP]
============================

"SBS Golfer" <Mr.Bogus@xxxxxxxxxxxxxxx> wrote in message
news:eHzqNtgPJHA.4776@xxxxxxxxxxxxxxxxxxxxxxx
The error message I get when trying to connect to the wireless network
is "Windows was unable to find a certificate to log you onto the
network "wireless network name".


"SBS Golfer" <Mr.Bogus@xxxxxxxxxxxxxxx> wrote in message
news:%23z$EWqgPJHA.4312@xxxxxxxxxxxxxxxxxxxxxxx
Looks like the NG does not allow me to attach this word document. Can
I eamil it to you somewhere else? Thanks.

"Merv Porter [SBS-MVP]" <mwport@xxxxxxxxxxxxxxxxxxx> wrote in message
news:O1KPnPgPJHA.4224@xxxxxxxxxxxxxxxxxxxxxxx
This setup is the Airlink wireless attached to the 5-port switch?

Assumption: the DSL router-modem is 192.168.1.1

If so, try this...

LAN IP Address: 192.168.2.1
Static IP Address: 192.168.1.2
Static Subnet Mask: 255.255.255.0
Static Gateway: 192.168.1.1
Primary DNS: 192.168.1.1
Secondary DNS: 192.168.1.1

----------------------------------------------------------
Internet
|
DSL Modem-Router
| |
| | Switch
| | Airlink Router (static, WAN side, 192.168.1.2)
| ||
| | Airlink Router (LAN side, 192.168.2.1)
| | | |
| Wireless clients
|
SBS External NIC (192.168.1.3)
||
SBS Internal NIC
||
Switch
| | | | |
SBS LAN Workstations
----------------------------------------------------------

--
Merv Porter [SBS-MVP]
============================


"SBS Golfer" <Mr.Bogus@xxxxxxxxxxxxxxx> wrote in message
news:u9xt3EgPJHA.3884@xxxxxxxxxxxxxxxxxxxxxxx
Thanks Merv. you're the greatest. Here is what I see and what I
did.

LAN IP Address: 192.168.2.1
Static IP Address: external static ip
Static Subnet Mask: 255.255.255.248
Static Gateway: external gateway IP
Primary DNS: (points to my mail server providors DNS servers (SBS
Servers forwards DNS requsts to same IP's)
Secondary DNS


OK so now I'm almost there I think. I did the above and can now see
my wireless network when I do a search. It shows it is a
"security-enabled wireless network (WPA)". however when I go to
connect it shows all bars connected but appears it is in a
"Validating Identity" state.

"Merv Porter [SBS-MVP]" <mwport@xxxxxxxxxxxxxxxxxxx> wrote in
message news:OWxkVyfPJHA.4708@xxxxxxxxxxxxxxxxxxxxxxx
I believe the Airlink has default IP of 192.168.1.1. Connect the
Airlink wireless unit directly to a "non-domain" spare laptop or
workstation (give the laptop a static IP of 192.168.1.10) and
access the Airlink web interface by typing in 192.168.1.1 in a
browser window. Now change the IP scheme of the Airlink to
192.168.2.x. Then change the laptop IP to 192.168.2.10. You should
be able to get backup to the Airlink web interface now. Now turn
on DHCP for the Airlink and set the WAN IP to (static) 192.168.1.2.
You may have want to select WPA Personal (TKIP passphrase) for the
security of the Airlink wireless. Then connect the Airlink to the
5-port switch, set your laptop to get an IP automatically and test
to see if you can get a connection.

--
Merv Porter [SBS-MVP]
============================

"SBS Golfer" <Mr.Bogus@xxxxxxxxxxxxxxx> wrote in message
news:%23LxRrjfPJHA.4152@xxxxxxxxxxxxxxxxxxxxxxx
Hey Merv thanks for the input. My problem is that I can't get to
the browser interface of the wireless router and therefore cannot
input any information.


"Merv Porter [SBS-MVP]" <mwport@xxxxxxxxxxxxxxxxxxx> wrote in
message news:%233U%23vyePJHA.4916@xxxxxxxxxxxxxxxxxxxxxxx
I suspect it the "LAN side" of your DSL modem-router that is
192.168.1.1. If you can't set the Airlink up as a WAP (Wireless
Acccess Point), you may need to use it as a router with it's WAN
IP set to 192.168.1.2 (static with GW 192.168.1.1); then change
the Airlink's LAN side IP range to 192.168.2.x with the LAN side
of the wireless router set to 192.168.2.1. After that, turn on
DHCP for the wireless portion and test. At that point, a wireless
client should get an IP address of 192.168.2.x.

--
Merv Porter [SBS-MVP]
============================


"SBS Golfer" <Mr.Bogus@xxxxxxxxxxxxxxx> wrote in message
news:O$jPgVePJHA.5044@xxxxxxxxxxxxxxxxxxxxxxx
OK so again I can ping 192.168.1.1 however I can get a repy
from the defualt IP whether or not the wireless is plugged in
or not. So there must be another device out there I'm getting a
reply from.
I'm using my laptop with a static IP and a direct connection to
the 10/100 5-port switch.


"Merv Porter [SBS-MVP]" <mwport@xxxxxxxxxxxxxxxxxxx> wrote in
message news:%23maWyBePJHA.4304@xxxxxxxxxxxxxxxxxxxxxxx
Attach the Airlink to a port on your 5-port switch; give it a
static IP in the same range as the DSL router's LAN side and a
gateway of the DSL router itself; turn off any DHCP service
on the DSL router's LAN side; turn on the Airlink's DHCP
service; test to see if a laptop pick's up a wireless
connection from the Airlink.

--
Merv Porter [SBS-MVP]
============================

"SBS Golfer" <Mr.Bogus@xxxxxxxxxxxxxxx> wrote in message
news:uAU605dPJHA.588@xxxxxxxxxxxxxxxxxxxxxxx
I got a AirLink 101 54 Mbps 802.11G Wireless Router I want to
attach to my SBS network. I'm a bit unsure as to where I need
to place the router to work best. Here's my environment......

SBS 2003 Premium SP2 w/2 Nics
ISA 2004 SP3

We use a 1.5MB T1 DSL connection for our internet access.
Here is the network topology layout...........

Inbound Internet --> DSL Router --> 10/100 5-port Switch -->
External NIC SBS Server ---> Outbound Internal NIC SBS
Server ---> 1GB Switch ---> Patch Panels

Now I use the 5-port Switch so that I can utilize my
additional external IP's for testing and being outside the
firewall. I have 2 other Windows 2003 Standard member servers
that I connect directly into the 1GB Switch.

So my question is where along the line do I place the
wireless router. I tried removing the 10/100 5-port switch
and placing it there. I also tried connecting it to an
available port on the 10/100 5-port Switch which would be
outside my firewall which is ok for me.

I would like to use this so that we can have wireless in our
conference room to accomodate guests and clients who have
laptops.





























.

Relevant Pages

  • Re: Connect a Wireless Router to my SBS Network
    ... DSL Modem-Router ... wireless network when I do a search. ... IP scheme of the Airlink to 192.168.2.x. ... you may need to use it as a router with it's WAN IP set to ...
    (microsoft.public.windows.server.sbs)
  • Re: Change wireless configuration
    ... I have them set up for ICS over a Wireless system, set up in what I think ... ICS is a MS term. ... It allows one computer to share its Internet connection with other computers in a LAN situation. ... to the Wireless Router, the XP Pro PC is connected to the Router by a ...
    (alt.internet.wireless)
  • Re: DMZ / Firewall question
    ... Have a Netgear DSL modem/router with a DMZ port. ... LAN side of the router has a number of XP PCs. ...
    (microsoft.public.windowsxp.network_web)
  • Re: VPN over wireless
    ... You will still the need the Router to issue DHCP and wireless ... network but still access to the internet. ... LAN Router Wireless Router ...
    (microsoft.public.windows.server.sbs)
  • Re: DMZ / Firewall question
    ... Have a Netgear DSL modem/router with a DMZ port. ... LAN side of the router has a number of XP PCs. ... "DMZ" is really just a virtual server port, ...
    (microsoft.public.windowsxp.network_web)