Re: ISA 2004 setup fails on brand new SBS 2003 Premium installatio

Hi Graham,

The Change Server IP wizard can be at:

Server Management | Standard Management | Internet and Email | Change Server
IP Address

It will assist you in changing the SBS LAN NIC IP. The default for SBS 2003
is 192.168.16.1.

Another way is to change the LAN subnet in the router to be something like
192.168.10.x, putting the router at 192.168.10.1 and the WAN NIC at
192.168.10.2.

See the network configuration diagram at:

Two Nics, a static IP address, ISA, router
http://www.smallbizserver.net/Articles/tabid/266/articleType/ArticleView/articleId/76/Two-Nics-a-static-IP-address-ISA-router.aspx

There is also a KB article:

How to configure Internet access in Windows Small Business Server 2003
http://support.microsoft.com/default.aspx?scid=kb;en-us;825763

After you have the network physically set up, install ISA.

When everything is installed, run CEICW. One of Andy's articles shows you
how to use CEICW (Confgiure Email and Internet Connection Wizard)

CEICW Walkthrough
http://www.sbs-rocks.com/sbs2k3/sbs2k3-n2.htm

--
Merv Porter [SBS-MVP]
============================

"gocat2005" <gocat2005@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:07EB885E-F2FC-4193-BEBD-0EA60366A991@xxxxxxxxxxxxxxxx
Hi SG

Where would I find the "change server IP address wizard" and what would I
change the WAN adapter's IP address to be?

Regards
Graham

"SuperGumby [SBS MVP]" wrote:

two NICs in the same subnet is invalid. Run the 'change server IP address
wiz' (ie. DO NOT do it manually, use the wiz).

"gocat2005" <gocat2005@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:B73F93DC-2DA3-4196-A732-F0E11BA75A52@xxxxxxxxxxxxxxxx
Hello

SBS 2003 installed from CDs and setup procedures followed - all systems
working fine including RWW, OWA etc.. Now I want to install ISA 2004.

ISA install stops at the point where it tries to install MSDE 2000 SP4
with
error "The wizard cannot install ISA server 2004. Try to install it
again
by
restarting the wizard ... etc etc". When I restart the wizard the same
error
occurs at the same place in the process.

Any suggestions please?

2 Nics in server attached to LAN switch in the 192.168.0.1-255 range
with
fixed IPs. One NIC is in the DMZ - so it is directly attached to the
internet. The other NIC is local LAN.
DHCP and DNS provided by SBS server.

Windows IP Configuration

Host Name . . . . . . . . . . . . : sbs
Primary Dns Suffix . . . . . . . : mydomain.local
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : Yes
WINS Proxy Enabled. . . . . . . . : Yes
DNS Suffix Search List. . . . . . : mydomain.local

Ethernet adapter LAN:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom BCM5708C NetXtreme II
GigE
(NDIS
VBD Client)
Physical Address. . . . . . . . . : 00-1D-09-6B-1C-82
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.9
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . : 192.168.0.9
Primary WINS Server . . . . . . . : 192.168.0.9

Ethernet adapter WAN:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom BCM5708C NetXtreme II
GigE
(NDIS
VBD Client) #2
Physical Address. . . . . . . . . : 00-1D-09-6B-1C-84
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.10
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
DNS Servers . . . . . . . . . . . : 192.168.0.9
Primary WINS Server . . . . . . . : 192.168.0.9
NetBIOS over Tcpip. . . . . . . . : Disabled









.

Relevant Pages

  • Re: Configure VP on Server 2003 with single NIC
    ... They did change the wizard and the option ... > dial-up as the Remote Access configuration. ... > NT Server 4.0 and Server 2000 allow VPN configuration for a single NIC ... the standard wizard assumes you have two NICs. ...
    (microsoft.public.windows.server.networking)
  • Re: ISA 2004 setup fails on brand new SBS 2003 Premium installatio
    ... Thanks Merv - I found the change server IP wizard - but that just changes the ... LAN IP and we don't want to change the whole LAN. ... I run the CEICW wizard and connect to the internet no problem. ... I run ISA 2004 install and it stops when it progresses to installing MSDE ...
    (microsoft.public.windows.server.sbs)
  • Re: Configure VP on Server 2003 with single NIC
    ... the standard wizard assumes you have two NICs. ... the other wizard options to enable remote access on the server. ... > Routing and Remote Access services on a box with a single NIC card? ...
    (microsoft.public.windows.server.networking)
  • Re: No DNS
    ... Both NICs should have static IPs and they must be in different subnets ... SBS Server should be running DHCP, DNS, WINS ... There is a wizard on the server console called CHANGE SERVER IP ...
    (microsoft.public.windows.server.sbs)
  • Re: Win2K RRAS/VPN Help
    ... having two NICs in the same IP subnet is a bad idea (especially ... Your server will still ... machines are using the Linksys as their default gateway they can all plug ... LAN clients would use the server's LAN NIC as their default gateway, ...
    (microsoft.public.win2000.ras_routing)