Re: ISA 2004 setup fails on brand new SBS 2003 Premium installatio

Hi SG

Where would I find the "change server IP address wizard" and what would I
change the WAN adapter's IP address to be?

Regards
Graham

"SuperGumby [SBS MVP]" wrote:

two NICs in the same subnet is invalid. Run the 'change server IP address
wiz' (ie. DO NOT do it manually, use the wiz).

"gocat2005" <gocat2005@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:B73F93DC-2DA3-4196-A732-F0E11BA75A52@xxxxxxxxxxxxxxxx
Hello

SBS 2003 installed from CDs and setup procedures followed - all systems
working fine including RWW, OWA etc.. Now I want to install ISA 2004.

ISA install stops at the point where it tries to install MSDE 2000 SP4
with
error "The wizard cannot install ISA server 2004. Try to install it again
by
restarting the wizard ... etc etc". When I restart the wizard the same
error
occurs at the same place in the process.

Any suggestions please?

2 Nics in server attached to LAN switch in the 192.168.0.1-255 range with
fixed IPs. One NIC is in the DMZ - so it is directly attached to the
internet. The other NIC is local LAN.
DHCP and DNS provided by SBS server.

Windows IP Configuration

Host Name . . . . . . . . . . . . : sbs
Primary Dns Suffix . . . . . . . : mydomain.local
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : Yes
WINS Proxy Enabled. . . . . . . . : Yes
DNS Suffix Search List. . . . . . : mydomain.local

Ethernet adapter LAN:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom BCM5708C NetXtreme II GigE
(NDIS
VBD Client)
Physical Address. . . . . . . . . : 00-1D-09-6B-1C-82
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.9
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DNS Servers . . . . . . . . . . . : 192.168.0.9
Primary WINS Server . . . . . . . : 192.168.0.9

Ethernet adapter WAN:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom BCM5708C NetXtreme II GigE
(NDIS
VBD Client) #2
Physical Address. . . . . . . . . : 00-1D-09-6B-1C-84
DHCP Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.10
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
DNS Servers . . . . . . . . . . . : 192.168.0.9
Primary WINS Server . . . . . . . : 192.168.0.9
NetBIOS over Tcpip. . . . . . . . : Disabled







.

Relevant Pages

  • Re: Cant find add license wizard / server management console
    ... a clients server to solve a tricky issue and I shadow their session. ... wander around in DNS and DHCP and Exchange they let the Wizard do it. ... If you can't do a fresh install then at least an install on top and then go ... > the post install setup wizard, then you couldn't use your server properly. ...
    (microsoft.public.windows.server.sbs)
  • Re: ISA 2004 setup fails on brand new SBS 2003 Premium installatio
    ... Thanks Merv - I found the change server IP wizard - but that just changes the ... LAN IP and we don't want to change the whole LAN. ... I run the CEICW wizard and connect to the internet no problem. ... I run ISA 2004 install and it stops when it progresses to installing MSDE ...
    (microsoft.public.windows.server.sbs)
  • Re: ISA 2004 setup fails on brand new SBS 2003 Premium installatio
    ... At present I am wiping the server and starting again (which is really ... so one trick is to rename it and run the install ... The two NICs in my SBS are now in different subnets. ... I run the CEICW wizard and connect to the internet no problem. ...
    (microsoft.public.windows.server.sbs)
  • Re: cannot browse from client, me too
    ... Did you rerun the internet connection wizard after you uninstalled the ISA? ... DNS server should be the internal IP address of the server. ... > I am not a professional, buy I have enough knowledge to install and setup ...
    (microsoft.public.windows.server.sbs)
  • Re: SBS 2003 beginner
    ... SO this wizard may help my user problems? ... Problem is when I look at users in the Server Manager and try to connect to the user he is not there. ... As far as I know DHCP is not on in the server yet. ... manually (rather than through the wiz) there's actually another wiz which ...
    (microsoft.public.windows.server.sbs)