Re: FTP login problem

Tech-Archive recommends: Repair Windows Errors & Optimize Windows Performance

Are you using Stadard or Premium with ISA installed?

--
Frank McCallister SBS MVP
MCP Microsoft Small Business Specialist
COMPUMAC

"HelpinFL" <HelpinFL@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message news:148640DA-35F9-4DF2-8842-E89FFAEF53D3@xxxxxxxxxxxxxxxx
I have had no problem accessing the default FTP on port 21, but when I setup
another FTP with a different port like 22 my browser nor FTP client will go
through. The FTP client (Cute FTP) shows the progress of connecting,
accepting the port, authenticating. When it acts like it's going to go into
the folder it says:

[1/20/2008 12:34:55 AM] 227 Entering Passive Mode (192,168,1,10,116,29).
COMMAND:> [1/20/2008 12:34:55 AM] LIST
STATUS:> [1/20/2008 12:34:55 AM] Substituting received PASV address
192.168.1.10 to server address 74.xx.xx.xx.xx.
STATUS:> [1/20/2008 12:34:55 AM] Connecting FTP data socket...
74.xx.xx.xx:29725...
ERROR:> [1/20/2008 12:35:16 AM] The connection failed due to an error or
timeout.

1) Verify that the destination IP address is correct.
2)crease the connection timeout threshold under Global Settings | Connection.
3) Switch to the opposite data connection type (PASV or PORT) under Site
Settings | Type tab.
4) Verify that the problem is not local by trying to connect to an alternate
server.
5) If a server name was used, verify it resolves to the correct address.
6) If using a local server table for server name resolution, check to see
that it doesn't resolve to an obsolete address.
7) Try pinging the address.
8) If you are using a router, verify the router is up and running (check by
pinging it and then ping an address outside of the router).
9) Do a traceroute to the destination to verify all routers along the
connection path are operational.
10) Verify that your subnet mask is setup properly.
11) Verify that your local software or hardware firewall is not blocking
outbound connections originating from CuteFTP.
12) Verify that your anti-virus software is not at fault (try disabling it).
ERROR:> [1/20/2008 12:35:16 AM] PASV failed, trying PORT.

500 Invalid PORT Command.

The Firewall Port 22 is open pointing to 192.168.1.10 and IIS firewall
allows port 22.

As I said the default FTP is working fine and this FTP is setup the same
with the exception of the port number.

Please help...Thanks.

.

Relevant Pages

  • RE: Telnet/ftp problems SBS2000
    ... Please make sure your client computers are configured as both Firewall ... will find two options "Enable folder view for FTP sites" and "Use Passive ... that the control connection has been successfully established, ... (other than port 21) ...
    (microsoft.public.windows.server.sbs)
  • Re: IPSwitch, Inc. WS_FTP Server
    ... > bounce attack as well as PASV connection hijacking. ... > The FTP bounce vulnerability allows a remote attacker to cause the ... > anonymously along with any internal addresses that the FTP server has ... That means it's got to handle a PORT ...
    (Bugtraq)
  • RE: FTP Window of opportunity?
    ... target on the line when in reality it was just a firewall lying to them. ... The connection connects and then immediately ... Subject: FTP Window of opportunity? ... the FTP port shows up. ...
    (Pen-Test)
  • Re: Iptables FTP question
    ... think all other related would be from specific modules,the FTP and IRC ... Keep in mind that connection ... source port of 20 if it is for port mode data connections(for a standard ... I would also break down your rules into chains instead of appending such ...
    (comp.security.firewalls)
  • Re: Passive means what during FTP?
    ... :227 Entering Passive Mode ... :ftp: connect: No route to host ... The FTP data transfer uses a connection that is separate from the ... address and port number to connect to for the data transfer. ...
    (comp.os.linux.setup)