Re: GPO causing client security logs to fill?

LDD15 wrote:
Domain Controller OU? Can you clarify?

In Active Directory all the Domain Controllers (SBS included) are placed in
a special (OU - organizational unit). Amoungst other reasons, this allows
special group policy to be applied only to the domain contollers.



"kj" wrote:

LDD15 wrote:
Here is the order

GPO
Enforced GPO Status
Small Business Server Domain Password Policy No
Enabled Small Business Server Windows Firewall No
Enabled
Small Business Server Internet Connection Firewall No
Enabled Small Business Server Remote Assistance Policy No
User configuration settings disabled
Small Business Server Client Computer No
Enabled
Small Business Server Lockout Policy No
User configuration settings disabled
Default Domain Policy Yes
Enabled
Basic SUS Config No
Enabled
User Restriction Policy No
Enabled
IE HomePage
Yes Enabled
Default Domain Controllers Policy No
Enabled


A little hard to read with the line wrap, but.

Default Domain Controller policy should not be linked to the domain
- only the Domain Controller OU.

Default Domain Policy should be at the bottom (last on the list) and
NOT "enforced".

I have access to only one SBS server at the moment, but I believe
this is the proper order for the domain policies should look like
the attached sbsgpo.pdf



"kj" wrote:

LDD15 wrote:
In answer to both of your questions, I am pasting the text from a
previous thread below. In summary we were having a sudden issue
with client logon failures. In this same newsgroup I posted a
thread titled "Client Logon Failure". Below are two sections of
text that result from that thread and from an email which was
external to the thread. I am under the impression that all of
this work was for not as I believe the actual problem was a
result of Time32 issues.

In summary, the following was changed. I modified the account
lockout policies as instructed below. This was done in the Group
Policy Objects. I realize that as a rule you are only supposed to
change the linked GPO's as opposed to the actual GPO's themselves.
However, I did find an article in the MS KB that said that
account/password items should be changed in the actual GPO's.

So basically, the Account lockout threshold, account lockout
duration and the account lockout reset where changed. I believe
this was changed in both the Default Domain Policy and the Default
Domain Controller Policy.

Also, per recommendations a linked GPO was made to the Default
Domain Controller Policy to set the "required password complexity
requirements" to enabled.

If this is not enough info please let me know.

First, Password policy (in SBS) should be set using the wizard and
only is effective when linked on the Domain (Small Business Domain
Password Policy, Small Business Server Lockout Policy). Second
adding another policy link probably changed the GPO precedence.
Also, it is not really a good idea to modify "default (domain or
domain controller) policy settings. It's better to add additional
Group Policy Objects then link accordingly and order precedence.

Unfortunately the recommendations are not Small Business Server
specific rather a generic Windows 2003 / AD. I may be missing it,
but I don't see where any GPO linking change was suggested.

If you have the details of what new GPO links were made, I'd
consider undoing (unlinking) the new links.

Btw, Audit log settings for the client computers are set in the
"Small Business Client Computers" Group Policy Object and I beleive
should be at link precendece order 3 in the domain policy list.
Perhaps post a list what policies you have linked there and what
order they are in.


Thank you both.
_________________________________________________________________________
From: Terence Liu (CS&S) [mailto:v-terliu@xxxxxxxxxxxxx]
Sent: Thursday, June 14, 2007 7:01 AM
To: Don Emerson
Subject: RE: Client Logon Failure (39270465-Client Logon Failure)

Hello Don,

Thank you for kind update.

In your client even log, I find many error message 1053:

Event Type: Error
Event Source: Userenv
Event Category: None
Event ID: 1053
Date: 2007-2-10
Time: 14:06:27
User: NT AUTHORITY\SYSTEM
Computer: MARMAC1

Description:

Windows cannot determine the user or computer name. (An internal
error occurred. ). Group Policy processing aborted.

1. I agree with you. This is mostly a virus related issue. The
other 2 workstations may infected by virus from this problematic
client.

Therefore, how about the step 1#? Do you find any virus from the
client?

Please try to install the antivirus on all client computers and
SBS, update the virus definition to latest and perform full virus
scan on the computers. If you do not have anti-virus application
installed, you may try: http://housecall.trendmicro.com/.

2. When you do clean boot on the client computer, you have to
logon as Administrators member account. I suggest you logon the
problematic client with local administrator and then do the clean
boot to test.

3. You can try to reboot the client and enter to Safe Mode (with
network), then try to logon domain. Is it fine?

Based on my research, the behavior can happen when the virus
activity that guessed the password, or the machine password is not
properly sync between SBS and internal clients. I suggest we try
the following steps to see if we can resolve this issue:

1. Enable complicated password policy.

Note: The Password Policy need to be configured in Default Domain
policy.

We can configure the settings under:

Computer Configuration\Windows Settings\Security Settings\Account
Policies\Password Policy

2. Configure account lockout policy.

Generally, it is a best practices suggestion to set the Threshold
value to 10 or higher. This is high enough to rule out user error
and low enough to deter hackers, especially when the password
complexity policy is enabled.

For medium security requirement, the recommended configurations
are:

Reset account lockout counter after: 30
Account lockout duration: 30
Account Lockout Threshold: 10

For high security requirement, the recommendations are:

Reset account lockout counter after: 30
Account lockout duration: 0
Account Lockout Threshold: 10

For more information, please refer to:

Account Passwords and Policies
http://www.microsoft.com/technet/prodtechnol/windowsserver2003/technologies/security/bpactlck.mspx

3. Check your firewall to ensure that only the necessary ports are
opened.

4. Ensure the above settings have been successfully applied.

1) On the problematic SBS server, please run the following command
to refresh the group policy changes:

GPUPDAGE /FORCE

2) Run SECPOL.MSC and check the above changed password, Account
lockout and auditing policies to see their effective settings, and
ensure that the policies have been applied successfully.

If the policies have been applied successfully, we should have
enhanced the security protection of that server.

5. The issue may occur if the remote SBS server sends broadcast
packets to the network. I suggest you change the "nolmhash" value
to "0" in the following registry key on the SBS server:

HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\LSA

Reboot the server for this change to take effect and check if the
event
does not appear.

6. If the event still appears, go to
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\lanmanserver\Parameters
and set "enablesecuritysignature" and "requiresecuritysignature"
to "0". Reboot the server and check if everything is OK.

7. There are several running processes on the computer that will
attempt to connect using the machine account.

This behavior can happen when the machine password is not properly
sync.

In order to reset the machine account password of a domain
controller use:

NETDOM RESETPWD /Server:ServerName /UsedD:Administrator
/PasswordD:*

The syntax of this command is:

NETDOM RESETPWD /Server:domain-controller /UserD:user
/PasswordD:[password | *]

NETDOM RESETPWD Resets the machine account password for the domain
controller on which this command is run. Currently there is no
support for resetting the machine password of a remote machine or
a member server. All parameters must be specified.

/Server Name of a specific domain controller that should
have its

machine account password reset.

/UserD User account used to make the connection with the
domain

controller specified by the /Server argument.

/PasswordD Password of the user account specified with
/UserD. A * means

to prompt for the password

After completing the command, reboot the server.

If we can not resolve the issue after we perform the above steps,
please kindly help me collect some information for further
investigation:

Please send the Server Performance report to me.

Hope these steps will give you some help.

Thanks and have a nice day!

Terence Liu

________________________________________________________________________
Hello Customer,

Thank you for posting here.

According to your description, I understand that you notice that
one of the client computer have several logon failures through a
day. If I have misunderstood the problem, please don't hesitate
to let me know.

First, please let me know:

1. Does this problem happen every day?
2. How do you notice the logon failures?

Based on my research, the virus or 3rd-party software may relate
to this issue. I suggest we try the following steps to see if we
can resolve this issue:

1. Please try to install the antivirus on this client computer,
update the virus definition to latest and perform full virus scan
on the computers. If you do not have anti-virus application
installed, you may try: http://housecall.trendmicro.com/.

2. Please do a clean boot on the client computer to narrow down
this issue:

To clean boot the problematic computer, please use the steps
below: a. Click Start, click Run, and then in the Open box, type
"MSCONFIG" (without the quotation marks). Click OK.

b. In the System Configuration Utility (MSConfig) window, click to
select the Selective Startup button.

c. Click to clear the check mark from the "Load startup items"
below Selective Startup.

d. Click the Services tab, click to check the "Hide All Microsoft
Services" box, and remove all the check marks from the remained
Non-Microsoft Services.

--
/kj


.