Re: Can only connect to local RWW, over internet cannot

Hi Costas,

It has a hardware sonicwall firewall. The user has lost the password so
before resetting this I brought in 3com officeconnect. did all the usual
setup of this configured firewall ports as below. Wont connect. I turned off
firewall and tryed with no luck.

Is there any way of testing connections to port 4125

Maybe it needs a RWW reinstall?

"Costas" wrote:

This is most probably a firewall issue. I would start by disabling the
firewall on the router and see if you can access the remote. If not, then
re-enable the firewall (with the forwarded ports as you have them now) and
move to the server. If you have two NICs on the server then go to Routing
and Remote Access and check the basic firewall to make sure that the 4125
port is open. I know you said that you run CEICW but these checks are for
the 'just in case' scenario.

Costas



"Dave Mc" <DaveMc@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:DCCD1D5A-17B3-4857-8415-0C821BDA5289@xxxxxxxxxxxxxxxx
Hi Costa,

It is standard edition, sp1 with security updates

"Costas" wrote:

Dave,

Is this a Standard Edition? (No ISA)? R2? Is SP2 installed?

Costas



"Dave Mc" <DaveMc@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:F12E6E26-EA93-4DA6-A261-7B21C3509DD6@xxxxxxxxxxxxxxxx
Hi Costa,

No (though I wish!) I am connecting to https://mail.test.com/remote
I can logon to owa no prob, when I try logon to server IT waits for
ages
and
comes back with error begining "Could not connect to the..
When I connect locally Its ok (https://127.0.0.1/remote)

I have restared iis, stopped IAC, restared default website, companyweb,
recreated ssl certificate twice through ciecw

Any ideas Please


"Costas" wrote:

You don't use the 127.0.0.1 IP address to access the server over the
Internet, do you?

Costas


"Dave Mc" <DaveMc@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:2E552AA1-570A-4052-836A-257841B58156@xxxxxxxxxxxxxxxx
Hi There,
I can connect to https://127.0.0.1/remote but cannot connect over
the
internet.
I have checked 3com router and forwarding 4125 443 & 3389 to the
server

I can connect to outside RWW from this server I am working on

I have run ceiw tool, recreated ssl cert, Run remote access tool etc

I think it maybe corrupt any ideas please, is it possible to
reinstall
RWW

Regards
Dave



.

Relevant Pages

  • Re: Interesting webserver intrusion (apache 1.3.31, mod_ssl 2.8.18, php 4.3.7)
    ... > fairly tight(only allowing 4 ports in), but perhaps I could tighten it ... The host systems firewall rules govern the access to the jailed system. ... What connections does your server need to ... Perhaps there is a 0-day for your ftp server out there. ...
    (Incidents)
  • Re: CEICW fails at firewall config
    ... Do you or do you not have ISA 2000 or ISA 2004 installed on the SBS server? ... Do you have 2 NICs in the SBS? ... CEICW fails on firewall configuration every time. ... >>> Call to Creating the protected networks access rule returned ok. ...
    (microsoft.public.windows.server.sbs)
  • Re: Add 2nd NIC after intial install?
    ... My biggest question with 1 NIC is: even if workstations are protected with individual firewall products, what is protecting the SBS server itself if ports are open for remote access through the Linksys firewall? ...
    (microsoft.public.windows.server.sbs)
  • Re: Recycler security issues on IIS server
    ... > latest upates to the server. ... > like to see the server put behind our firewall, ... other software, install all patches, IISlockdown, URLscan, use the correct ... the procedures you follow may vary depending on your security needs. ...
    (microsoft.public.inetserver.iis.security)
  • Re: Source Code to Filter out WindowsMessenger POP-UPS
    ... Zone Alarm does NOT support 'server'. ... Very few ports are open, ... >What you are asking for amounts to a firewall. ... I would NOT search for source code to compile ...
    (microsoft.public.inetserver.iis.security)
Loading