RE: Your message did not reach some or all of the intended recipie
- From: Ian <Ian@xxxxxxxxxxxxxxxxxxxxxxxxx>
- Date: Mon, 12 Sep 2005 22:22:01 -0700
Nathan,
Sorry but I did miss understand your commands, anyway here are the results
and answers from your previous questions.
_____________________________________________________________________
______________________________________________________________________
Your Question 1.
My misunderstanding. Here are the results
220 AHSSBS03.allanhogansolicitors.local Microsoft ESMTP MAIL Service, Version
..0.3790.1830 ready at Tue, 13 Sep 2005 14:03:41 +1000
helo domain.com
250 AHSSBS03.allanhogansolicitors.local Hello [10.0.0.1]
mail from:allan.hogan@xxxxxxxxxxx
250 2.1.0 allan.hogan@xxxxxxxxxxxxxxxxxxxxx OK
rcpt to:allan.hogan@xxxxxxxxxxx
250 2.1.5 allan.hogan@xxxxxxxxxxx
Your Question 2.
I did not have this ticked, send HELO is now ticked.
Your Question 3.
Sending External Email & Occurs with all users
Your Question 4.
I created user accounts through Active Directory Users and Computers, but I
have noticed that Allan Hogan who is the boss does not appear in Active
Directory but appears in the Standard Management User List, I did recreate
his account via Active Directory but has disappeared again.
Your Question 5.
Yes the login script appears there.
Your Question 6.
AllanHogan@xxxxxxxxxxxxxxxxxxxxxxxxxx is set to primary, should I add
another SMTP address with there actual address which is
allan.hogan@xxxxxxxxxxx?
Your Question 7.
Yes I have setup POP Accounts, for all staff as they are allowed to have
additional mail boxes with bigpond.
Your Question 8.
Customer does not have a domain name
Your Question 9.
It was listening to the server's IP Address 10.0.0.1, changed it to 'All
Unassigned'
_____________________________________________________________________
--
Ian Campbell
""Nathan Liu [MSFT]"" wrote:
> Hi Ian,
>
> Thank you for your reply.
>
> 1. For the error message "mail from: 501 5.5.4 Invalid Address", if we
> haven't input any valid email address at the back of the 'mail from: '
> command line, we will receive the "501 5.5.4 Invalid Address" error
> message. For more instruction of the Telnet command line, please kindly
> refer to the following KB article:
>
> XFOR: Telnet to Port 25 of IMC to Test IMC Communication:
> http://support.microsoft.com/?id=153119
>
> 2. Did you have click 'Send HELO instead of EHLO' check box in the
> 'SmallBusiness SMTP connector' Properties?
>
> 3. For the NDR error message "<AHSSBS03.allanhogansolicitors.local
> #5.5.0 smtp;553 allanhogansolicitors.local does not exist>", does this
> issue occur when you send email to internal or external recipients? Does
> this issue occur with all users or certain users?
>
> 4. Did you run through CEICW (Standard Management, To Do List) to
> configure the SBS options? How did you create the SBS users, by using the
> ''Add User'' wizard (Standard Management, Users)?
>
> 5. If the users are created by using the ''Add a user'' wizard (which
> can be located in ''Server Management'' '' ''Standard Management'' ''
> ''Users''), ''SBS_LOGIN_SCRIPT.bat'' will be set in ''Logon script''
> (dsa.msc '' User object's Properties '' the ''Profile'' tab.) Please check
> if this it is set correctly.
>
> 6. What email recipient policy is set for the users, the one you are
> prompted to input when running CEICW (in the ''E-mail Domain Name'' page)?
> In the properties of the user (dsa.msc, %domain name%, MyBusiness, Users,
> SBSUsers), tab Email addresses, you should see the same domain name set as
> ''SMTP Primary''.
>
> 7. Additionally, are you using the POP3 Connector to retrieve incoming
> emails?
>
> 8. It seems that the remote mail server is denying SMTP connections that
> fail reverse lookup. You should contact your ISP and make sure your domain
> is not on their list of unsolicited commercial email. More details on this
> please check out:
>
> 300580 XCON: Cannot Send E-Mail Messages to a Growing List of Domains
> http://support.microsoft.com/?id=300580
>
> 9. Please also make sure Default SMTP Virtual Server is listening 'All
> Unassigned':
>
> A. Open Exchange System Manager.
> B. Expand Servers | Your server | Protocols | SMTP, right-click Default
> SMTP Virtual Server and click Properties.
> C. What IP address is the server listening on?
>
> I appreciate your time and cooperation. If anything is unclear, please feel
> free to let me know. I am looking forward to hearing from you.
>
> Best regards,
>
> Nathan Liu (MSFT)
> Microsoft CSS Online Newsgroup Support
>
> Get Secure! - www.microsoft.com/security
> ======================================================
> This newsgroup only focuses on SBS technical issues. If you have issues
> regarding other Microsoft products, you'd better post in the corresponding
> newsgroups so that they can be resolved in an efficient and timely manner.
> You can locate the newsgroup here:
> http://www.microsoft.com/communities/newsgroups/en-us/default.aspx
>
> When opening a new thread via the web interface, we recommend you check the
> "Notify me of replies" box to receive e-mail notifications when there are
> any updates in your thread. When responding to posts via your newsreader,
> please "Reply to Group" so that others may learn and benefit from your
> issue.
>
> Microsoft engineers can only focus on one issue per thread. Although we
> provide other information for your reference, we recommend you post
> different incidents in different threads to keep the thread clean. In doing
> so, it will ensure your issues are resolved in a timely manner.
>
> For urgent issues, you may want to contact Microsoft CSS directly. Please
> check http://support.microsoft.com for regional support phone numbers.
>
> Any input or comments in this thread are highly appreciated.
> ======================================================
> This posting is provided "AS IS" with no warranties, and confers no rights.
>
> --------------------
> >Thread-Topic: Your message did not reach some or all of the intended
> recipie
> >thread-index: AcW0PTT94BRctOn+QCC5IWEbs6wJqg==
> >X-WBNR-Posting-Host: 144.131.133.122
> >From: =?Utf-8?B?SWFu?= <Ian@xxxxxxxxxxxxxxxxxxxxxxxxx>
> >References: <C8026CBE-2A16-4629-89F3-D5A9EFD0D610@xxxxxxxxxxxxx>
> <ADoa4mdsFHA.3308@xxxxxxxxxxxxxxxxxxxxx>
> <B8C103C3-D1BE-4166-9CC7-8D0AFB73222E@xxxxxxxxxxxxx>
> <05758678-9399-4420-AE5A-47D8B0433EE1@xxxxxxxxxxxxx>
> <Yyb7ELrsFHA.2848@xxxxxxxxxxxxxxxxxxxxx>
> >Subject: RE: Your message did not reach some or all of the intended recipie
> >Date: Wed, 7 Sep 2005 23:19:02 -0700
> >Lines: 321
> >Message-ID: <4893595D-1085-4F4B-AB72-E9288512F064@xxxxxxxxxxxxx>
> >MIME-Version: 1.0
> >Content-Type: text/plain;
> > charset="Utf-8"
> >Content-Transfer-Encoding: 7bit
> >X-Newsreader: Microsoft CDO for Windows 2000
> >Content-Class: urn:content-classes:message
> >Importance: normal
> >Priority: normal
> >X-MimeOLE: Produced By Microsoft MimeOLE V6.00.3790.0
> >Newsgroups: microsoft.public.windows.server.sbs
> >NNTP-Posting-Host: TK2MSFTNGXA03.phx.gbl 10.40.2.250
> >Path: TK2MSFTNGXA02.phx.gbl!TK2MSFTNGXA03.phx.gbl
> >Xref: TK2MSFTNGXA02.phx.gbl microsoft.public.windows.server.sbs:203132
> >X-Tomcat-NG: microsoft.public.windows.server.sbs
> >
> >Hi Nathan,
> >
> >I have configured the settings to smart host
> >
> >In your details you are saying to type the following command
> >
> >'mail from:' and press enter even when I do this on my server where my
> >is working fine I still get the following error message,
> >
> >mail from:
> >501 5.5.4 Invalid Address
> >
> >How easy is it just to uninstall exchange and reinstall ?
> >
> >
> >--
> > Ian Campbell
> >
> >
> >""Nathan Liu [MSFT]"" wrote:
> >
> >> Hi Ian,
> >>
> >> Thank you for your update.
> >>
> >> To narrow down this issue, please refer to the below information:
> >>
> >> I. For the error message "mailfrom: 500 5.3.3 Unrecognized command,
> >> from: 501 5.5.4 Invalid Address", please understand if we type the
> >> incorrect SMTP telnet command, we will receive the "Unrecognized
> command"
> >> error message, we must re-open a new command prompt, then re-establish
> the
> >> SMTP telnet session. Thanks for your understanding.
> >>
> >> Step 1: When the issue happens again, in the Exchange Server, please
> telnet
> >> the destination mail server which you cannot send mail to by the
> following
> >> steps.
> >>
> >> 1. Click 'Start', click 'Run', type 'telnet', and then click 'OK'.
> >>
> >> 2. At the Microsoft Telnet command prompt, type 'open server_name 25',
> and
> >> then press ENTER.
> >>
> >> 3. To verify that you are successfully connected to the SMTP Mail
> Service,
> >> type 'helo domain.com', and then press ENTER.
> >>
> >> 4. Type 'mail from:' , and then press ENTER.
> >>
> >> 5. Type 'rcpt to:', and then press ENTER.
> >>
> >> 6. Type "quit" (without the quotation marks), and then press 'ENTER' two
> >> times to close the connection to the server and leave the Telnet session
> >> running.
> >>
> >>
> >> Step 2: When the issue happens again, in the Exchange Server, please
> telnet
> >> the destination mail server which you cannot send mail to by the
> following
> >> steps.
> >>
> >> 1. Click 'Start', click 'Run', type 'telnet', and then click 'OK'.
> >>
> >> 2. At the Microsoft Telnet command prompt, type 'open server_name 25',
> and
> >> then press ENTER.
> >>
> >> 3. To verify that you are successfully connected to the SMTP Mail
> Service,
> >> type 'ehlo domain.com', and then press ENTER.
> >>
> >> 4. Type 'mail from:' , and then press ENTER.
> >>
> >> 5. Type 'rcpt to:', and then press ENTER.
> >>
> >> 6. Type "quit" (without the quotation marks), and then press 'ENTER' two
> >> times to close the connection to the server and leave the Telnet session
> >> running.
> >> More detailed information:
> >>
> >> XFOR: Telnet to Port 25 of IMC to Test IMC Communication:
> >> http://support.microsoft.com/?id=153119
> >>
> >> II. Did you switch to forward to smarthost to deliver emails? You can
> >> refer to the detailed steps in my previous reply.
> >>
> >> III. If the issue persists, please perform the below steps:
> >>
> >> 1. Open the Server Management console, go to DomainName(Exchange) ->
> >> Connectors, right click 'SmallBusiness SMTP connector' and select
> >> Properties.
> >>
> >> 2. In the dialog box, click the Advanced tab, click the 'Send HELO
> instead
> >> of EHLO' check box, then click Apply.
> >>
> >> 3. Please check if the issue can be reproduced.
> >>
> >> I appreciate your time and cooperation. If anything is unclear, please
> feel
> >> free to let me know. I am looking forward to hearing from you.
> >>
> >> Best regards,
> >>
> >> Nathan Liu (MSFT)
> >> Microsoft CSS Online Newsgroup Support
> >>
> >> Get Secure! - www.microsoft.com/security
> >> ======================================================
> >> This newsgroup only focuses on SBS technical issues. If you have issues
> >> regarding other Microsoft products, you'd better post in the
> corresponding
> >> newsgroups so that they can be resolved in an efficient and timely
> manner.
> >> You can locate the newsgroup here:
> >> http://www.microsoft.com/communities/newsgroups/en-us/default.aspx
> >>
> >> When opening a new thread via the web interface, we recommend you check
> the
> >> "Notify me of replies" box to receive e-mail notifications when there
> are
> >> any updates in your thread. When responding to posts via your
> newsreader,
> >> please "Reply to Group" so that others may learn and benefit from your
> >> issue.
> >>
> >> Microsoft engineers can only focus on one issue per thread. Although we
> >> provide other information for your reference, we recommend you post
> >> different incidents in different threads to keep the thread clean. In
> doing
> >> so, it will ensure your issues are resolved in a timely manner.
> >>
> >> For urgent issues, you may want to contact Microsoft CSS directly.
> Please
> >> check http://support.microsoft.com for regional support phone numbers.
> >>
> >> Any input or comments in this thread are highly appreciated.
> >> ======================================================
> >> This posting is provided "AS IS" with no warranties, and confers no
> rights.
> >>
> >> --------------------
> >> >Thread-Topic: Your message did not reach some or all of the intended
> >> recipie
> >> >thread-index: AcWyn7KaufjPq44TQouWmfMx57a3qg==
> >> >X-WBNR-Posting-Host: 144.134.225.123
> >> >From: =?Utf-8?B?SWFu?= <Ian@xxxxxxxxxxxxxxxxxxxxxxxxx>
> >> >References: <C8026CBE-2A16-4629-89F3-D5A9EFD0D610@xxxxxxxxxxxxx>
> >> <ADoa4mdsFHA.3308@xxxxxxxxxxxxxxxxxxxxx>
> >> <B8C103C3-D1BE-4166-9CC7-8D0AFB73222E@xxxxxxxxxxxxx>
> >> >Subject: RE: Your message did not reach some or all of the intended
> recipie
> >> >Date: Mon, 5 Sep 2005 21:59:01 -0700
> >> >Lines: 263
> >> >Message-ID: <05758678-9399-4420-AE5A-47D8B0433EE1@xxxxxxxxxxxxx>
> >> >MIME-Version: 1.0
> >> >Content-Type: text/plain;
> >> > charset="Utf-8"
> >> >Content-Transfer-Encoding: 7bit
> >> >X-Newsreader: Microsoft CDO for Windows 2000
> >> >Content-Class: urn:content-classes:message
> >> >Importance: normal
> >> >Priority: normal
> >> >X-MimeOLE: Produced By Microsoft MimeOLE V6.00.3790.0
> >> >Newsgroups: microsoft.public.windows.server.sbs
> >> >NNTP-Posting-Host: TK2MSFTNGXA03.phx.gbl 10.40.2.250
> >> >Path: TK2MSFTNGXA01.phx.gbl!TK2MSFTNGXA03.phx.gbl
> >> >Xref: TK2MSFTNGXA01.phx.gbl microsoft.public.windows.server.sbs:151047
> >> >X-Tomcat-NG: microsoft.public.windows.server.sbs
> >> >
> >> >Just tried to send another email to my own address.
> >> >
> >> >
.
- Follow-Ups:
- RE: Your message did not reach some or all of the intended recipie
- From: "Nathan Liu [MSFT]"
- RE: Your message did not reach some or all of the intended recipie
- References:
- Your message did not reach some or all of the intended recipients.
- From: Ian
- RE: Your message did not reach some or all of the intended recipients.
- From: "Nathan Liu [MSFT]"
- RE: Your message did not reach some or all of the intended recipie
- From: Ian
- RE: Your message did not reach some or all of the intended recipie
- From: Ian
- RE: Your message did not reach some or all of the intended recipie
- From: "Nathan Liu [MSFT]"
- RE: Your message did not reach some or all of the intended recipie
- From: Ian
- RE: Your message did not reach some or all of the intended recipie
- From: "Nathan Liu [MSFT]"
- Your message did not reach some or all of the intended recipients.
- Prev by Date: Re: sbs sp1 and isa 2004
- Next by Date: Re: SBS2003 migration to new SBS2003 server and domain
- Previous by thread: RE: Your message did not reach some or all of the intended recipie
- Next by thread: RE: Your message did not reach some or all of the intended recipie
- Index(es):
Relevant Pages
|
