RE: Mysterious problem on my client's Windows Server 2003 Network

Hi,

Look for a duplex mismatch - for example, if one end (say, the server) of a
cable is configured to 100Mbps full duplex and the other end (the switch) to
automatic, the automatic end will gear down to 10Mbps half duplex (many
people miss the fact that configuring specific parameters always turn
autonegotiation off - you MUST configure both ends identically or leave them
on automatic). You will get an immense amount of checksum errors and TCP
retransmits on traffic going from the full duplex end to the auto end -
enough for the checksummming algorithm not being able to detect them all,
letting occasional packets slip by with corrupted payload...

If the auto end (or actually, the end that currently runs half duplex on a
link where the other end runs full duplex) is manageable, you may see reports
of a lot of "late collisions" as well.

Also note that there are switches that have weird autonegotiation algorithms
and sometimes create duplex/speed mismatch without showing it (3com,
notably). A software upgrade usually cures that.

Again: EACH end of a cable must be either set to "auto" or to the same speed
and duplex, or BAD things will happen.

This can be especially tricky when you have fiber media converters between
switches in the network. They are often configured to negotiate even though
you WILL get severe problems if both ends don't happen to land on the same
parameters.

Later,
Pete
--
Peter Josefson, Specialisthuset, Sweden


"CoolHandJoe" wrote:

Hi all

I've been troubleshooting a problem a client of mine is having that had
practically disabled the entire network. It was all at random they
would lose connection to the server and/or connection to the internet,
also they started having corrupt pst files while using roaming
profiles. Now, I've since discovered that the problem was actually due
to at least two different things one of which was a rogue router with
the same address as the router they actually use that had DHCP turned
on but DHCP was being handled by the server. However, all the clients
were receiving the proper information for DNS so we couldn't tell until
we entered the IP address of the main router (Linksys) and got a prompt
for a D-Link DI-604. It was obvious after that. Anyway, there is still
corruption going on and people getting disconnected from the server and
losing information. There are no errors anywhere and roaming profiles
have been disabled so that corruption doesn't occur to files being
copied. We've had professionals come in and test the cables and they're
all fine, I installed a new network card in the server though there
wasn't anything to indicate a problem with the first one. Throughout
this process I ran Ethereal a few times and there were always many many
errors about bad checksums from the server to any of the machines that
were trying to transfer information but it wasn't any computer in
particular it was any computer. I want to include that there were many
dropped packets in some cases it was 9500 of 10000 that got dropped but
they were all the ones using smb. So, just a quick recap, from computer
to server no errors from server to computer error. I suspect that's the
server telling the computer that the received data is corrupt. I'm
getting them a new switch for Monday and I've done some performance
monitoring that doesn't look out of place compared to the baseline and
if anything it's lower across the board because of the disabled roaming
profiles.
Anyone have any idea where I should look and what I can do to hunt down
the source of this problem?

Joe


.

Relevant Pages

  • Re: [9.04] printing with lpd: remove duplex options
    ... I just upgraded the server to 9.04. ... Now all options, like Duplex, disappear! ... Stopping printers step by step, ... after transfert with lpd on the server, ...
    (Ubuntu)
  • Re: Truly bizarre NIC (?) problem
    ... match in duplex - we are set to 100/full and the switch is at 100/half. ... Check with your network people to see what speed the port is configured to on ... ES&SO Server Planning and Integration ... "server1a" is a second 10/100 ethernet adapter. ...
    (AIX-L)
  • Re: Slow File Copy to 2000 Server Mac OS 10
    ... I would check for a speed / duplex mismatch on the network card / switch. ... Mac's have a lot of trouble connecting if there is any speed duplex ... even if it is on the server side. ...
    (microsoft.public.win2000.macintosh)
  • Re: Duplex unit
    ... the only bypass for the settings misbehaviour we have found is to ... the print server, Windows 2000 and XP computers discover that the Duplexing ... > Duplex unit is shown as installed. ... > carry through to the clients since a network printer on the client uses ...
    (microsoft.public.win2000.printing)
  • Re: Configuring LDAP on Entourage 2004 OS X
    ... Microsoft CSS Online Newsgroup Support ... with Blackberry's because RIM's blackberry enterprise server works. ... Configuring LDAP on Entourage 2004 OS X ... does not work with a self signed SSL certificate OR with the SSL ...
    (microsoft.public.windows.server.sbs)