Re: Page Fault BSOD during application install

Tech-Archive recommends: Repair Windows Errors & Optimize Windows Performance

Looking forward for your response. :)

--
Jabez Gan [MVP]
Microsoft MVP: Windows Server
http://www.blizhosting.com
MSBLOG: http://msblog.resdev.net


"Lynn" <Lynn@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:CCA4AAA7-B4F0-4368-A666-A2470CA25708@xxxxxxxxxxxxxxxx
Ok, will try uninstalling that update, if that doesn't work will do memory
swap and see if that helps. Will post results tomorrow. Thanks!

"Lynn" wrote:

I can try but will be later. Further info: After initial post, did more
snooping. Found that these messages started appearing on 12/7/05,
immediately
after I installed 2 MS Windows updates (Nov. Malicious SW Removal Tool
and
Sec Update KB896424). I had also installed software "A" earlier that day.
It
never did work correctly, so I uninstalled on 3/19 and re-tried
installation
of network package "B". Still get BSOD, still at MDAC install, but this
time
with "IRQL less than or not equal". I noticed that there are still
registry
entries for "A", and cannot delete them; did not see any evidence that
any of
it is active, though. Don't know if this is helpful information or not.

"Jabez Gan [MVP]" wrote:

Can you try swapping RAM and see if you are still getting this issue?

Also,
http://www.eventid.net/display.asp?eventid=2003&eventno=705&source=Perflib&phase=1



--
Jabez Gan [MVP]
Microsoft MVP: Windows Server
http://www.blizhosting.com
MSBLOG: http://msblog.resdev.net


"Lynn" <Lynn@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:36AA6E5D-4997-4194-8093-6E450C04B13B@xxxxxxxxxxxxxxxx
Win SBS 2K3; installing network version of application. Crashes every
time
when reaches MDAC portion of install. Get "Page fault in non-paged
area"
blue
screen. See same errors in Event Viewer/Application right before
every
crash,
but they also happen at other times. WinMgt Event ID 63 (PerfProv had
been
registered in WMI namespace..) and Perflib Event ID 2003 (config info
for
...\aspperf.dll for the "ASP" service does not match the trusted perf
libr
info stored in the registry). Vendor claims they haven't seen this
problem
on other installs, I can actually install stand-alone version on
workstation
successfully. Thanks for all suggestions.





.

Relevant Pages

  • Re: Reinstall windows installer
    ... If there's no way to uninstall it, ... Microsoft MVP: Windows Server ... MSBLOG: http://msblog.resdev.net ...
    (microsoft.public.windows.server.general)
  • Re: Windows SP1 Update problem via Windows Update
    ... Microsoft MVP: Windows Server ... I would like to get SP1 installed without getting this CRYPTUI.dll error. ... How can we install SP1 without this error? ...
    (microsoft.public.windows.server.general)
  • Re: Page Fault BSOD during application install
    ... Microsoft MVP: Windows Server ... MSBLOG: http://msblog.resdev.net ... Still get BSOD, still at MDAC install, but this ...
    (microsoft.public.windows.server.general)
  • Re: 2003 Standard SP1 Boot Problem
    ... Microsoft MVP: Windows Server ... > upgrade. ... > This was a clean install, withe the disk partitioned into C and D ...
    (microsoft.public.windows.server.general)
  • Re: Cant install components on 2003 SP1 R2 upgrade
    ... Microsoft MVP: Windows Server ... The install went okay as far as I can tell though. ... I have a Server 2003 Enterprise SP1 Active/Passive cluster and I've ...
    (microsoft.public.windows.server.setup)