Re: 2003 Ent Mutimedia Server
From: Steve (anonymous_at_discussions.microsoft.com)
Date: 04/16/04
- Next message: Gary: "Physical disk size limitation"
- Previous message: Laura E. Hunter \(MVP\): "Re: DHCP"
- In reply to: Larry Samuels: "Re: 2003 Ent Mutimedia Server"
- Next in thread: Larry Samuels: "Re: 2003 Ent Mutimedia Server"
- Reply: Larry Samuels: "Re: 2003 Ent Mutimedia Server"
- Messages sorted by: [ date ] [ thread ]
Date: Fri, 16 Apr 2004 11:02:12 -0700
This did not fix the problem. The media player error I am
getting is when I click on "more information"
is "0xC00D1198: Cannot connect to the server". I have
opened every port none to man!
>-----Original Message-----
>Use Port 80 or put the streaming server in the DMZ.
>HOWTO: Set Up Windows Media Services 9 Series to Use HTTP
Streaming on Port
>80 with IIS 6.0 Installed
>Applies To
>This article was previously published under Q328728
>SUMMARY
>The Microsoft Windows Media Services (WMS) and Microsoft
Internet
>Information Services (IIS) can coexist on a computer when
you use their
>default values. By default, WMS does not enable the WMS
HTTP Server Control
>Protocol plug-in. In this manner, IIS can safely bind to
port 80 for
>delivery of Web-based content.
>
>Sometimes it can be useful for WMS to use port 80 to
deliver content. For
>example, if the majority of a content provider's clients
are behind a
>firewall, it can be better to use port 80 for delivery of
streaming content,
>because most firewalls have port 80 opened.
>
>With IIS 6.0, HTTP requests are handled by the Http.sys
listener. By
>default, Http.sys will listen to all requests coming in
on port 80 for all
>IP addresses bound to the computer (except for the
loopback address:
>127.0.0.1). For WMS to bind to use port 80 for streaming
content, you must
>configure the Http.sys listener so that WMS can listen to
the specified IP
>addresses. If you enable the HTTP Server Control Protocol
plug-in without
>configuring the listener, you may receive the following
error:
>
>One usage of each socket address (protocol/network
address/port) is
>permitted. Verify that other services (such as IIS) or
applications are not
>attempting to use the same port and then try to enable
the plug-in again.
>
>Error Code: 0xC00D158B
>MORE INFORMATION
>For both IIS and WMS to use port 80, one of the following
two conditions
>must be true:
> a.. One (1) network adapter has at least 2 IPs bound to
the adapter.
> b.. Two (2) network adapters have at least 1 IP bound
to each adapter.
>If either of these conditions is true, follow these steps
to configure the
>listener:
> 1.. From a command prompt, type the appropriate command
to stop the
>following services:
> a.. Windows Media Services: net stop wmserver
> b.. Internet Information Services: net stop iisadmin
> c.. Http.sys Listener: net stop http
> 2.. Run the WMSHttpSysCfg utility (located at
>%systemroot%\system32\windows
media\server\admin\mmc\WMSHttpSysCfg.exe).
> 3.. Add the IP addresses that you want Http.sys to
listen to. The
>addresses that Http.sys does not listen to are available
for WMS to use. (If
>this list is blank, Http.sys listens to all non-loopback
IP addresses).
> 4.. Click OK to close the dialog box.
> 5.. Restart the services that you stopped in step 1
(including, but not
>limited to):
> a.. Http.sys Listener: net start http
> b.. World Wide Web Publishing Service or IIS Admin:
net start w3svc
> c.. Windows Media Services: net start wmserver
> 6.. Configure WMS HTTP Server Control Protocol:
> 1.. Start WMS Admin MMC.
> 2.. Select the server name.
> 3.. Click the Properties tab, and then click Control
Protocols.
> 4.. If it is not already disabled (or if it is In
Error), right-click
>WMS HTTP Server Control Protocol, and then click Disable.
> 5.. Right-click WMS HTTP Server Control Protocol, and
then click
>Properties.
> 6.. Click Allow selected IP addresses to use this
protocol.
> 7.. Select the IP addresses that you want to deliver
content over port
>80.
>
> NOTE: Do not select the same IP addresses as the ones
that you added to
>the Http.sys listener in step 3, otherwise the plug-in
might go into an
>error state when it is enabled.
> 8.. Set the plug-in to Use default port (80).
> 9.. Click Apply, and then click OK to close the
dialog box.
> 10.. Right-click WMS HTTP Server Control Protocol,
and then click
>Enable.
>At this point, you can expect that WMS is streaming media
content over port
>80 for the IPs selected in the control plug-in, and that
Http.sys is
>handling all other port 80 requests.
>
>IMPORTANT: Other applications might make a configuration
utility that can
>change the Http.sys IP listen list. When you restart the
Http.sys service
>the next time, it can bind to port 80 on an address
selected by WMS and
>might cause the control plug-in to go into an error state.
>
>For additional information about running Windows Media
Services v4.1 with
>IIS 5.0, click the article number below to view the
article in the Microsoft
>Knowledge Base:
>268585 Running IIS 5.0 and Windows Media Services with
HTTP Streaming
>
>The information in this article applies to:
> a.. Microsoft Windows Media Services 9 Series
> b.. Microsoft Internet Information Services version 6.0
> Last Reviewed: 1/16/2004 (2.1)
> Keywords: kbDSWWMM2003Swept kbinfo KB328728
>
>
>--
>Larry Samuels MS-MVP (Windows-Shell/User)
>Associate Expert
>Unofficial FAQ for Windows Server 2003 at
>http://pelos.us/SERVER.htm
>Expert Zone - www.microsoft.com/windowsxp/expertzone
>"Steve" <anonymous@discussions.microsoft.com> wrote in
message
>news:1d34c01c42339$83445ca0$a401280a@phx.gbl...
>> I recently installed mutimedia server and have a page
>> configured on my website to stream audio via media
>> player. I can stream audio via the website while I am
on
>> my lan, but not from an external site. I get a "unable
to
>> connect to server" message. I am sure there is a port
>> that needs to be opened on the firewall, but I can't
find
>> any info. Any Ideas?
>>
>> Thanks
>
>
>.
>
- Next message: Gary: "Physical disk size limitation"
- Previous message: Laura E. Hunter \(MVP\): "Re: DHCP"
- In reply to: Larry Samuels: "Re: 2003 Ent Mutimedia Server"
- Next in thread: Larry Samuels: "Re: 2003 Ent Mutimedia Server"
- Reply: Larry Samuels: "Re: 2003 Ent Mutimedia Server"
- Messages sorted by: [ date ] [ thread ]
Relevant Pages
|
|
