Re: WLB with multiple secondary IPs?
From: TwistedPair (twistedpair_at_mail.com)
Date: 07/22/04
- Next message: John Toner [MVP]: "Re: lost switch fabric on one node causes total cluster failure"
- Previous message: Nick: "File Share resource failed to start"
- In reply to: Mahmood [MSFT]: "Re: WLB with multiple secondary IPs?"
- Next in thread: Mahmood [MSFT]: "Re: WLB with multiple secondary IPs?"
- Reply: Mahmood [MSFT]: "Re: WLB with multiple secondary IPs?"
- Messages sorted by: [ date ] [ thread ]
Date: Thu, 22 Jul 2004 07:18:59 -0700
Hi,
Thank you for responding. Is this for windows 2003 or NT? This sounds like
instructions for Windows NT. When I go into control panel, there is a
"Network Connections" folder, and both of my adapters are visible when I
click on it. I don't see the protocol tab, or the WLBS Virtual NIC. Thank
you again for your help.
"Mahmood [MSFT]" <a-makhta@online.microsoft.com> wrote in message
news:40fefd28$1@news.microsoft.com...
> If you look into the article it is explaining how you can bind more than
one
> IP to for load balacing. You have to repeat the steps on each of your node
> in cluster. Only one address will be used as dedicated IP address and all
> secondary IP address will be load balanced.
>
>
> To configure WLBS to load balance more than one virtual IP address:
> 1.. Click Start, point to Settings, click Control Panel, and then
> double-click Network.
> 2.. Click the Protocols tab, click TCP/IP, and then click Properties.
> 3.. In the Adapter box, click WLBS Virtual NIC.
> 4.. Click Advanced, add the IP addresses you want WLBS to load balance,
> and then click OK.
> 5.. Close Control Panel, and then restart the computer.
>
>
> "TwistedPair" <twistedpair@mail.com> wrote in message
> news:uKAfP21bEHA.2340@TK2MSFTNGP10.phx.gbl...
> > Hi,
> > Thank you for helping me. I actually need there to be 1 VIP per site,
and
> > there are 4 sites, and each has a different IP. The article you sent me
> > describes how to set it up with only 1 IP address.
> >
> > " You can type only one virtual IP address in the WLBS Setup dialog box.
> > However, all IP addresses bound to the virtual network adapter are load
> > balanced, with the exception of the dedicated IP address"
> >
> > Also, I forgot to mention this is with Windows2003. Any ideas?
> >
> >
> >
> > "Mahmood [MSFT]" <a-makhta@online.microsoft.com> wrote in message
> > news:40febb8e@news.microsoft.com...
> >> You can configure more than one IP address for load balancing.
> >>
> >> How to Configure WLBS with Multiple Virtual IP Addresses
> >> http://support.microsoft.com/default.aspx?scid=KB;EN-US;232000
> >>
> >>
> >> "TwistedPair" <twistedpair@mail.com> wrote in message
> >> news:%23790RH0bEHA.2660@tk2msftngp13.phx.gbl...
> >> > Hi All,
> >> > I have websites bound to several IP addresses (primary and secondary)
> >> > on
> >> > two
> >> > servers that I want to load balance. Do any of you know of any
> > tutorials
> >> > that show how to handle this scenario?
> >> >
> >> > Thanks,
> >> > Pair
> >> >
> >> >
> >>
> >>
> >
> >
>
>
- Next message: John Toner [MVP]: "Re: lost switch fabric on one node causes total cluster failure"
- Previous message: Nick: "File Share resource failed to start"
- In reply to: Mahmood [MSFT]: "Re: WLB with multiple secondary IPs?"
- Next in thread: Mahmood [MSFT]: "Re: WLB with multiple secondary IPs?"
- Reply: Mahmood [MSFT]: "Re: WLB with multiple secondary IPs?"
- Messages sorted by: [ date ] [ thread ]
Relevant Pages
|
