Re: Help! Issues Installing XP MCE!

Do you mean make a copy of the disks with Nero or something like that?

I had attempted to copy the contents of the CD onto a folder on the hard
drive when Win 98 SE was installed on it to try to start the installation
process from the hard drive and had no problems coping it.

"JW" wrote:

> Do you have a running system that you can try copying the content of the CD
> to to see if there might be an actual problem with the CD itself.?
>
> "DAN" <DAN@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
> news:ED64EE97-195C-4016-9FED-367B1E7D80C4@xxxxxxxxxxxxxxxx
> > Yes. I used the the Format with the install CD, I even used FDisk when
> > booting from a floppy and a program called Wipeout.
> >
> > I've also changed the hard drive and kept just one stick of 128 known to
> > work ram. Even the IDE ribbon cables were changed to see if there maybe
> > was
> > a short somewhere. At one point I had the hard drive and the DVD/CD drive
> > on
> > one IDE cable as master and slave respectfully in that order). I then
> > seperated them onto 2 different IDE Controllers and set both as Master.
> >
> > Also replaced the power supply and tried a different DVD/CD drive.
> >
> > The only constant in this whole equation has been the Pentium 4 3 GHz CPU
> > and the ECS Photon PF1 ver 1.0 with an updated bios. Also just remembered
> > that the video card has been constant throughout this.
> >
> > I've also disabled Hyperthreading on the CPU.
> >
> > Like I said before, I'm going "Nucking Futs" trying to figure this out.
> >
> > "JW" wrote:
> >
> >> Did you also erase the partition where you are installing in and recreate
> >> it
> >> and format it with using the install CD?
> >>
> >> "DAN" <DAN@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
> >> news:36318B29-BC4C-404E-BB22-940CA4FFFB51@xxxxxxxxxxxxxxxx
> >> > At first I tried it with NTFS, then after many attempts I tried it with
> >> > Fat32
> >> > but no luck.
> >> >
> >> > "JW" wrote:
> >> >
> >> >> Did you format the drive with Fat32 or NTFS?
> >> >>
> >> >> "DAN" <DAN@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
> >> >> news:9B185457-C527-441A-B307-515EF0530020@xxxxxxxxxxxxxxxx
> >> >> > I'm trying to install Media Center on a PC I built. I have it set
> >> >> > to
> >> >> > just
> >> >> > bare-bones. I am able to format the drive w/ no issue. The problem
> >> >> > starts
> >> >> > when the installation starts to copy the files to the drive. It
> >> >> > reaches
> >> >> > about 19-29 percent and then the system just reboots!!!! I even
> >> >> > tried
> >> >> > just
> >> >> > for craps and giggles install Win98 SE and that worked w/ no issues.
> >> >> > I'm
> >> >> > at
> >> >> > wits end with this. PLEASE HELP!
> >> >>
> >> >>
> >> >>
> >>
> >>
> >>
>
>
>
.

Relevant Pages

  • Re: Help! Issues Installing XP MCE!
    ... > one IDE cable as master and slave respectfully in that order). ... > seperated them onto 2 different IDE Controllers and set both as Master. ... > The only constant in this whole equation has been the Pentium 4 3 GHz CPU ... >> and format it with using the install CD? ...
    (microsoft.public.windows.mediacenter)
  • Re: Install Sata drivers
    ... >>> beacause it already includes all the required sata, raid, etc drivers. ... >>the purposes of allowing WinXP to install without pressing F6. ... > connected via IDE -- i.e., there's no necessity for these drives to ...
    (alt.comp.periphs.mainboard.asus)
  • Re: ide disk not found on SATA port
    ... So, he bought a IDE ... Although - to be truthful - if the motherboard is not recognizing the ... Install your brother's present PATA HDD in a USB external hard drive ... Check his motherboard user's guide to see if it's necessary to install ...
    (microsoft.public.windowsxp.help_and_support)
  • Re: OT: new PC catch-22
    ... Master, Primary Slave,Seconsdary Master and Secondary Slave all have the ... You have a problem with the BIOS, IDE cables, or BIOS setup. ... However, each cloned drive then can be quickly configured by the user, making each one unique and look as if they had done not only a fresh install but also installed all of that software. ...
    (sci.electronics.design)
  • Re: DVD-ROM and CD-RW not working after upgrade
    ... boot off your XP CD, choose to format NTFS, and install Windows ... >>8/4/32A CD-RW jumpered slave on my secondary IDE. ... >>and I was going to replace it with an Artec 16X DVD-ROM ... My bios detects all drives ...
    (microsoft.public.windowsxp.hardware)