Re: XP Upgrade install problem


Hi John,

I have not been able to boot to Windows since the first reboot
after the screwed up Install. The CD won't run in DOS. Your tip was
good, I ran the Winnt file from DOS and the install went ok.
However, during the install I was asked to choose between a repair
or go ahead with the install. I made the mistake of choosing to
continue the install. This wiped out the Windows folder and created
a new XP Windows folder. So I ended up with a new XP install and
many of my programs wouldn't work. Lost the desktop shortcuts,
Re-installing all my programs that depend on the Registry would take
a week. I was led to believe I could restore my old system from
Add/Remove in Control Panel but it wasn't there.

Sooo, I renamed Windows to WinXP and my backup folder from Winsav to
Windows from DOS. I re-booted and I'm back to Win98 SE. Everything
seems to be working including programs on my D: and E: partitions..
I'm glad I copied Windows into a new Winsav folder before I started
the Upgrade. I can rename them back and boot to XP if there is a
need. Or I can run the Upgrade again now that I'm back to 98SE.

I may try the upgrade again but I'll do more preparations.
Still don't understand why the CD won't boot in DOS and Setup.exe
won't run either but the Winnt file runs Setup, although it looks a
little different.

Thanks your help John, I really appreciate it.

Regards,

Bill Watt
Win98 Computer Help & Other Information http://home.ptd.net/~bwatt/

________________________________________________________________

On Tue, 18 Nov 2008 18:37:41 -0400, "John John (MVP)"
<audetweld@xxxxxxxxxxx> wrote:

It goes into a chkdsk when? When you boot to the Windows XP CD you will
not get a chkdsk unless you request one, you will go either to the
Repair option via the Recovery Console, where you can then request a
chkdsk, or to the install the operating system option. Are you making
it that far when you boot with the XP cd? You say that the XP logo
comes up, it sounds to me like you are not booting to the cd at all.

To start the installation from DOS launch the winnt command from its
i386 folder location on the CD-ROM.
http://support.microsoft.com/kb/307848 If you cannot boot from the CD
you can also use the 6 floppy diskette setup boot disk set, the set can
be downloaded from the Microsoft site:
http://support.microsoft.com/kb/310994

Upgrades from Windows 98 can be problematic. To better your chances of
a successful upgrade you should do a bit of house keeping on the Windows
98 installation before you upgrade it. Get rid of all your temp files,
empty your Recycle Bin, turn off or uninstall all software that is set
to start automatically when the computer starts, this is especially
important for software that uses file system drivers, AntiVirus software
is an example of software that uses file system drivers. Also
disconnect all unnecessary external hardware before you begin the
installation, the only external hardware that you should have connected
is the monitor keyboard and mouse.

John

Bill Watt wrote:

Hi John.

Yes, CD-Floppy-HD. The boot accesses the CD but then goes into the
disk check then reboots and keeps repeating it. I ran Scandisk on
both drives, no problems plus the machine has been working great. I
found Chkdsk but it wouldn't run in DOS. The XP logo comes up at
boot then starts the disk check.

I don't understand why Setup won't run in DOS. I have proof of
previous versions. Suppose the drive was new? I backed up the
Windows folder before I ran Setup so I could rename it from DOS if
needed but setup deleted it. I printed the Upgrade Report during
Setup but I don't see anything there that could cause the problem.
Just some programs that may not run.

I have work to do on the machine so I may have to try to restore my
98 SE backup from DOS and forget XP.

Thanks for your response.

Regards,

Bill Watt
______________________________________________________--
On Tue, 18 Nov 2008 08:21:04 -0400, "John John (MVP)"
<audetweld@xxxxxxxxxxx> wrote:


Is the BIOS boot order set to boot to the CD before the hard disk?

John

Bill Watt wrote:


Trying to install XP Pro Upgrade over Win98 SE on my PC.
The install goes to the end. However, the desktop is in two
sections, the top 1/3 is at the bottom and can't be accessed.
I removed some icons then rebooted using ctrl-alt-del. Could not get
to the start Menu.
When it came up it checked drive C:. It fixed a few errors, like a
couple of file sizes. Then it re-booted and checked again and
re-booted.
It checks then reboots without getting into Windows every time.
The XP CD is not recognized. Tried booting with a Win98SE floppy
with CD support and run Setup from the CD, bur the message says it
can't run in Dos mode.

Without being able to access the CD I can't do a repair or much
else.

I have the Win98 SE system backed up on drive 2 in the machine, also
Setup said I could Uninstall from Add/Remove Programs and restore my
Win98 SE system but I can't get into Windows. I have too much
important data to do a clean install. I suppose I could fdisk C:
then copy the Win98 SE backup over.

I checked all the groups and this one seemed the most appropriate,
if not please advise.

I'm using my XP PRO Notebook for this but all my data and hundreds
of programs are on the PC.

I would like to get XP on the PC.

Would appreciate any ideas.

Regards,

Bill Watt
Win98 Computer Help & Other Information http://home.ptd.net/~bwatt/





.

Relevant Pages

  • Re: Start Menu, Icons Not Appearing
    ... Also, make sure your system has no malware, download, install and run Ad ... Assuming your system is set to boot from the CD-ROM drive, ... To Setup Windows XP now, ... To Repair a Windows XP Installation using Recovery Console press R. ...
    (microsoft.public.windowsxp.accessibility)
  • Re: Cannot Boot Into any Option for Safe Mode
    ... NTLDR and NTDETECT.COM from the original XP CD maybe help? ... How To Create a Boot Disk for an NTFS or FAT Partition in Windows XP ... An upgrade will probably not fix anything where a clean install might. ...
    (microsoft.public.windowsxp.newusers)
  • Re: WINDOWS XP WONT BOOT
    ... you can to a repair install but you cannot do it ... Now, if a retail disk doesn't work, you could install XP to a different ... When I rebooted, it told me to hit> any key to start CD ROM boot and then it went back into> the same old screen as I originally described. ... The disc I was using> was the Windows XP disc that came with my Dell but since I> bought it, the hard drive had to be changed and I now have ...
    (microsoft.public.windowsxp.accessibility)
  • Re: PLEASE HELP: 2 ERROR MESSAGES
    ... The advice to do a repair install, turned out to be a grievous and expensive ... The repair install caused a corruption and windows became ... It seems as though it would not boot from the CD ...
    (microsoft.public.windowsxp.general)
  • Re: Automatic Downloads Activation Issues
    ... repair install as follows: ... NOTE, while a repair install should leave your data files intact, if ... Assuming your system is set to boot from the CD-ROM drive and you have an ... with the option to setup Windows or Repair Windows Installation ...
    (microsoft.public.windowsxp.accessibility)