Re: XP setup cannot detect hard disks

From: Carlos F (car_lost_at_yahoo.com.remove.this)
Date: 03/02/04


Date: Tue, 2 Mar 2004 13:38:34 -0500

Excellent suggestion!

Just to make sure I understand your:

- Disconnect one of the mirrored drives from the RAID controller and move it
to the IDE controller.
- Install XP onto this drive.
- Disconnect that drive from the IDE controller and move it to the RAID
controller.
- Rebuild the mirror using the RAID BIOS (making sure I copy the new XP boot
drive onto the blank drive)
- Reboot and pray.

Carlos

"Len Segal" <msn_news@ne_ws.oom> wrote in message
news:Oj$h96FAEHA.2180@TK2MSFTNGP09.phx.gbl...
> Carlos,
>
> Check the instructions for the Intel mobo! Some will require that you do
the
> install from the standard IDE controller and ONLY after installation is
> complete can you switch the cabling over to the RAID controller.
>
> This was specifically the case with my MSI mobo with built-in Promise RAID
> controller.
>
> --
>
> Regards,
> Len Segal, MCP
> Microsoft - MVP
> --------------
> My reply address is intentionally wrong to reduce SPAM Email.
> NOTE: We do not respond to unsolicited Email support questions,
> please post questions in newsgroup.
>
> "Carlos F" <car_lost@yahoo.com.remove.this> wrote in message
> news:%23quVaj8$DHA.2448@TK2MSFTNGP12.phx.gbl...
> > Hello,
> >
> > I keep getting the dreaded "setup did not find any hard disk drives
> > installed in this computer" error message when i try to install windows
xp
> > pro.
> >
> > The computer is as follows:
> >
> > - intel p4
> > - intel S845WD1h motherboard
> > - the board has an integrated Promise PDC20267 IDE RAID controller
> > (FastTrack 100)
> > - two 80 GB hard drives connected to the RAID controller - configured as
a
> > single mirrored drive
> > - this computer was configured with Windows 2000 Pro and Windows 2000
> > Advanced Server. I used fdisk to delete all the partitions.
> >
> > I originally tried to run the XP install from the CD from Windows 2000
> > Advanced Server and ran into the "Stop 0x0000007B or
> > INACCESSIBLE_BOOT_DEVICE" error. I consulted the MSDN article covering
> this
> > issue (article # 324103). As per the article I did a virus scan. I found
> the
> > machine was rife with viruses - the person that used the machine before
> had
> > apparently not been too careful about cleaning the box. In order to save
> > time and clean the machine of any viruses I fdisked it. I then updated
the
> > BIOS to version 8 from the Intel site and I downloaded the RAID
controller
> > drivers from the Promise site.
> >
> > I ran the install process again by booting to the CD and hit F6 to
specify
> a
> > custom RAID controller. I selected the FastTrack 100 driver from the
list
> > the setup displayed. 10 seconds later setup asked what kind of setup to
> run
> > (XP install, repair XP install using recovery console etc). I selected
to
> > set up XP now. It then stated that setup did not find any hard disk
drives
> > installed in this computer. I have subsequently tried running the setup
> in
> > a 100 different permutations with no change in the end.
> >
> > I suspect that the controller, hard disks and the cables are ok. I am
> able
> > to access and configure the disks via the RAID controller BIOS. The
> > computer BIOS picks up the mirrored drive and lists it as an available
> hard
> > drive. Also, when the machine was running windows 2000 pro (which was
> right
> > before i tried installing XP) the mirrored drive was running just fine.
I
> > also checked the controller cables and the jumpers and everything is ok.
> >
> > Any suggestions? I am about to pull out what is left of my hair.
> >
> > Carlos
> >
> > --
> > Carlos Fernandez
> > Touzon Technologies, Inc.
> > Voice - (703) 725-1765
> > Fax - (703) 997-1093
> > Email - cfernandez@touzon.com
> > www.touzon.com
> >
> >
>
>



Relevant Pages

  • Re: [SLE] Added disk now no boot
    ... > I have this old Promise Ultra 100 card that supports 4 ide drives. ... > attached, then my RAID controller signs on like it used to, then I get ... The added controller's BIOS loads and prevents your normal boot with a drive ... Is your current RAID controller an actual PCI slot card or is it embedded on ...
    (SuSE)
  • Re: Bad RAID Configuration Need Rebuild 1st DC
    ... This is an embedded SATA RAID controller on an IBM x206 Series server. ... A during boot up and an IBM branded version of the Adaptec Storage Manager ... > level sync of the drives as per the instructions if this is not made ...
    (microsoft.public.windows.server.setup)
  • Re: IBM ServeRAID-3L reports drives to have 0GB capacity
    ... The drives are sitting behind a RAID controller. ... RAID controller which will then be presented to the o/s's storage subsystem. ... > Adapter: IBM ServeRAID-3L Ultra2 ...
    (comp.periphs.scsi)
  • Converting IDE RAID 1 to SATA RAID 1
    ... I have a server with an on-board IDE RAID controller controlling two IDE ... drives in a RAID 1 configuration. ... If I install a Promise TX2300 PCI-to-SATAII RAID controller and two SATAII ...
    (comp.sys.ibm.pc.hardware.storage)
  • Re: Best hardware to mirror IDE drives under FreeBSD?
    ... > mirrored drives. ... What is the best controller to use for this ... The 3ware 7000 series cards work great. ... I'd go with a 8000 series card and SATA drives for that. ...
    (freebsd-questions)

Loading