Re: HDD incorrectly labeled with new XP install

Hi John: Thank you so much for your help and insight. That's exactly what I
was doing (cussing) when this happened. To have to keep a watch & change the
drive letter everytime you install a piece of new S/W is not what I wanted to
do. I'm in the process of erasing the disk now and will be re-installing XP
with a new partition. I will follow your directions closely. Thanks again.
Mike

"John John" wrote:

You may as well completely flatten the installation and start again from
scratch, it's the only suitable way of fixing the boot volume letter
assignment. Read the instructions carefully at the drive/partition
screen and you will see that you will be offered the option to delete
the partition(s) then recreate it/them. Exit the installation after you
recreate the partition and reboot the computer and start again. Do a
proper full format and install on the newly formatted C drive, that
usually prevents these unexpected drive letter assignments. The problem
that you experienced is not unusual in these type of circumstances or
when a previous operating system is detected by the setup program.

If you chose to forgo the reinstallation then you will have to live with
Windows on drive D and cuss at it every time you use the computer ;-)

John

Michael wrote:

John: Appreciate the links. I'll definitely read them. The funny thing
though is during installation it did not ask me to partition the drive. It
found the drive and just asked to format it. I used the quick NTFS format
(did the full format on the previous attempted install) and then it proceded
to install the S/W. But you have given me the idea to erase the current
partition and partition it anew. Since my previous OS was W2K and my drive
was "C" I felt there was no need to go through the partitioning again but I
now will. Truthfully, I was ready to physically pull the drive and check the
jumper settings. I'll re-partition first. Thanks for your help.
Mike

"John John" wrote:


See here for an overview of how drive letters are assigned during XP Setup:
http://www.microsoft.com/technet/prodtechnol/winxppro/reskit/c12621675.mspx#ELNAC

The same information is here in a Windows 2000 explanation, pretty well
all the same for XP, just explained a bit differently:
http://support.microsoft.com/kb/234048/

The problem you describe sometimes happen when you create and format
more than one partition with the Windows Setup program. One way around
the problem is usually to exit the setup program after you create the
partition(s) then restart the setup operation. If the USB flash drive
is mistakenly detected as a fixed drive then remove the device for the
Windows installation then install it only after Windows is installed, if
needed unplug the cable that go from the motherboard to the USB port.

John

Michael wrote:


Hi: Here's a good one. Upgraded to XP from W2K last night. Went with a new
install not upgrade. Floppy is "A", CD is "D" but the HDD instead of being
"C" is now "E". Formatted and reinstalled twice with same result each time.
When I plug in my USB Flash drive it's labeled "C". What's going on? I'm
stumped.
Thanks,
Mike




.

Relevant Pages

  • Re: reformatting xp
    ... to do a low level format just to delete one partition. ... In order to do a very clean install you may want to download and ... format your primary partition and install XP. ... drives) and i just want to format one of the partitions. ...
    (microsoft.public.windowsxp.general)
  • Re: How do I label a disk?
    ... now I am going to definitely install solaris but I have this ... > to a dead disk. ... I tried to label it with the format command: ... format> partition ...
    (comp.unix.solaris)
  • Re: Installation Problem
    ... partition where you want to install Windows and do a new installation on ... the hard drives were apparently scrubbed before they ... Anyway, I ran the XP install CD and formatted the first drive, then ... The only thing left to do was format ...
    (microsoft.public.windowsxp.general)
  • Re: Adding a data partition on a new Dell XPS laptop
    ... Vista or Win7 won't install. ... Advanced and let Vista or Win7 do the NTFS formatting (overwriting the DD ... the partition to legacy cylinder-aligned. ... Using Acronis Disk Director you format a partition in NTFS; ...
    (alt.sys.pc-clone.dell)
  • Re: MS Whistler Personal
    ... You've not done this the right way, start again and format the C: partition to the NTFS file format and install XP on it. ... One thing for sure is that the partition on which you installed Windows is is way too small for an XP installation, you may as well delete the partition C: & F: and then create one large partition with the free space and format it NTFS. ... After you create and format the new partition exit the Windows setup program and reboot the computer and start the installation again and select to install XP on the new partition that you just formated earlier. ... The Windows XP CD is bootable so I don't know why it doesn't boot the computer, check that again and make sure you select the right boot order in the BIOS and then pay attention when the computer boots, you may have to press a key to boot the cd, you may see a message telling you to press a particular key to boot with the CD. ...
    (microsoft.public.windowsxp.help_and_support)