Re: Cannot connect to web with Client
- From: "Steve Winograd [MVP]" <bcmaven@xxxxxxxx>
- Date: Fri, 29 Dec 2006 19:29:12 -0700
In article <CE065CEE-6D5D-43D3-ADCB-DD9E6EB88467@xxxxxxxxxxxxx>, don
cole <doncole@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
I have two compters connected with a cross over cable.
Computer 1 (the host) has 2 Ethernet cards one going to internet(DSL
modem)(external). And one going to the other computer thru a cross over cable.
Computer 2 has `1 Ethernet card (that I am using) connected to the other end
of the crossover cable.
The file sharing works on both computers.
I can access the web on the host but not the client.
The bottom task bar on both computers shows a yellow '!' in the network
adapter.
Both computers are running windows XP.
I've been thru the wizzars help files a hundred times and cannot get anywhere.
At one time (going through the help files) I found a detailed way of reading
both the client and host IP Address, Subnet Mask and Default Gateway. It
said to write this stuff down and then how to change them to fit together. It
had a chart to show
how to do this. I lost that page and for the life of me I can't find it again.
I believe this may be my problem.
Any help appreciated,
Make sure that Internet Connection Sharing is enabled on the host:
1. Open the Network Connections folder.
2. Right-click the connection that goes to the DSL modem.
3. Click Properties.
4. Click Advanced.
5. Put a check mark in the box "Allow other network users to connect
through this computer's Internet connection."
6. If there's a box to select a home networking connection, select the
one that connects to the client computer.
7. Click OK.
To see a network connection's TCP/IP configuration:
1. Right-click the connection.
2. Click Status.
3. Click Support.
4. Click Details.
Thank you Steve,
I did as you said however when I click "Allow other network users to connect
through this computer's Internet connection." (on the host).
I no longer can connect to the internet on the host or anyhere.
You're welcome, Don. I suspect that you're sharing the wrong network
connection. Make sure that you're sharing the one that connects to
the DSL modem, not the one that connects to the other computer.
Sorry I connected with the internet card. Still can't access web on client.
I have one Ethenet wire comming from modem to host. And one Ethernet wire
going from host to Client. Is this all I need,?
When I click the share botton on host/internet card I can no long access web
with host.
Sharing the host's Internet connection should have no effect on the
host's web access.
Please post a news group reply showing the hosts's TCP/IP
configuration with sharing not enabled. To write the TCP/IP
configuration to a file, open a command prompt window (Start > Run >
cmd) and enter this line:
ipconfig /all >ipconfig.txt
Then copy/paste the contents of the "ipconfig.txt" file into your
reply.
--
Best Wishes,
Steve Winograd, MS-MVP (Windows Networking)
Please post any reply as a follow-up message in the news group
for everyone to see. I'm sorry, but I don't answer questions
addressed directly to me in E-mail or news groups.
Microsoft Most Valuable Professional Program
http://mvp.support.microsoft.com
.
- Follow-Ups:
- Re: Cannot connect to web with Client
- From: Steve Winograd [MVP]
- Re: Cannot connect to web with Client
- References:
- Re: Cannot connect to web with Client
- From: Steve Winograd [MVP]
- Re: Cannot connect to web with Client
- From: don cole
- Re: Cannot connect to web with Client
- From: Steve Winograd [MVP]
- Re: Cannot connect to web with Client
- From: don cole
- Re: Cannot connect to web with Client
- Prev by Date: Re: WEP problem, I think?
- Next by Date: Re: Cannot connect to web with Client
- Previous by thread: Re: Cannot connect to web with Client
- Next by thread: Re: Cannot connect to web with Client
- Index(es):
Relevant Pages
|
Loading