Re: One Gateway, Two Networks

Hi Doug,

Thanks for the fast reply. Following your feedback I think I've found the
right thing then (Netgear RP614 -
http://www.netgear.com/products/details/RP614.php).

So would my previous a) - e) be right if you replace the DG824s with the
RP614?

Just want to be sure before I go ahead and buy the things.

Thanks again

John


"Doug Sherman [MVP]" <dsherman@xxxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:usWk1r6QGHA.6084@xxxxxxxxxxxxxxxxxxxxxxx
No, Steve's solution contemplates that you would connect the WAN/Internet
port of the respective routers to LAN ethernet ports on the SpeedTouch. I
do not believe that your DG824M has a WAN/Internet ethernet port. If this
is the case, you would need a different router.

Doug Sherman
MCSE, MCSA, MCP+I, MVP

"John" <JohnSickOfSpam@xxxxxxx> wrote in message
news:#OBvIl6QGHA.5108@xxxxxxxxxxxxxxxxxxxxxxx
Hi Steve,

Thanks for your reply. I'm afraid I'm being a bit slow, so can I just
check
my thinking?

a) I connect my Netgear DG824M (Call this Netgear Router 1)
(http://kbserver.netgear.com/products/DG824M.asp) via one of its four
ethernet ports to one of the four ethernet ports on the DSL connected
Speedtouch 510 modem/router.

b) I do the same with a third router (maybe another DG824M). (Call this
Netgear Router 2)

c) I enable DHCP server on Speedtouch with IP range from 192.168.0.1 /
Subnet 255.255.255.0

d) I enable DHCP server on Netgear Router 1 with IP range from
192.168.1.1
/
Subnet 255.255.255.0

e) I enable DHCP server on Netgear Router 2 with IP range from
192.168.2.1
/
Subnet 255.255.255.0

The spec in the Netgear manual says:
..."The gateway incorporates Auto UplinkTM technology. Each LOCAL
Ethernet
port will automatically sense whether the Ethernet cable plugged into the
port should have a 'normal' connection such as to a PC or an 'uplink'
connection such as to a switch or hub. That port will then configure
itself
to the correct configuration."...

So I'm assuming this means its ok to use the LAN ports to connect to the
Speedtouch router?

Anyway, apologies for asking the same thing twice, but thanks for your
help.

Best regards

John

"Steve Winograd [MVP]" <bcmaven@xxxxxxxx> wrote in message
news:2htt021j46cqqrdg1bac8dbrraif74p64v@xxxxxxxxxx
In article <uyNERcqQGHA.1096@xxxxxxxxxxxxxxxxxxxx>, "John"
<JohnSickOfSpam@xxxxxxx> wrote:
Hi there,

Can anyone point me towards a good article on how to setup two
separate
networks from one broadband gateway router?

Background - I'm moving to a shared office, where they already have a
speedtouch broadband gateway with four ethernet ports (and I think a
dynamic
IP address). I've been using a similar setup in my previous office
with
a
Netgear DG824M gateway router. Both of us have been sharing our
various
folders on our networks, but now we we'll be sharing, I'd rather set
us
up
so that we can separate our two networks.

So what's the best approach? My networking knowledge is limited so
far
to
basic stuff (ie I know what NAT and POTS means but not how to set it
up)
and
so could do with some kind of walkthrough.

Hope I've been clear with what I'm trying to achieve!

Thanks in advance and best regards

John

PS - Both sets of PCs are using WinXP (mine are Pro, not sure yet
what
the
other are)

For complete isolation between the two networks, while giving Internet
access to the computers on both networks, use two more broadband
routers.

Connect the WAN (Internet) port on each additional router to a LAN
port on the Speedtouch gateway router. Connect the first business'
computers to LAN ports on the first additional router. Connect the
second business' computers to LAN ports on the second additional
router.

Thanks to you and Doug for your help. Are you able to point me towards
a
product & walkthrough that would take me through it?

Thanks again

John

You're welcome, John. The setup is simple. Any broadband router sold
at computer and office supply stores for home and small office use
will be fine. Connect everything as I said above. Make sure that the
two new routers use a different IP subnet than the old router. For
example, if the old router uses 192.168.1.x, configure the new routers
to use 192.168.0.x.
--
Best Wishes,
Steve Winograd, MS-MVP (Windows Networking)

Please post any reply as a follow-up message in the news group
for everyone to see. I'm sorry, but I don't answer questions
addressed directly to me in E-mail or news groups.

Microsoft Most Valuable Professional Program
http://mvp.support.microsoft.com






.

Relevant Pages

  • Re: Using Remote Desktop From an SBS Domain
    ... when you tried to RDP while attached directly to a port on your router? ... So if 3389 needs forwarded on the client end too then that is what the ... Hopefully next week I can attempt a connection while my ISP watches the ...
    (microsoft.public.windows.server.sbs)
  • How did they get behind my NAT?
    ... this point I panicked and shutdown the VNC service ASAP. ... My question is how the attacker got to my VNC port! ... the internet through the router. ... client connection using local port number 5900 (which was also being ...
    (alt.computer.security)
  • Re: Port 23
    ... I use Windows XP over a LAN connected to a Netgear Router. ... At some point in the past, port 23 was opened. ... Shields Up previouisly I saw full stealth on the computers. ...
    (microsoft.public.windowsxp.security_admin)
  • Re: One Gateway, Two Networks
    ... port of the respective routers to LAN ethernet ports on the SpeedTouch. ... you would need a different router. ...
    (microsoft.public.windowsxp.network_web)
  • Re: Connecting to Home Computer
    ... cannot transmit IP packets outside the local network). ... assigned by your router. ... You have to add the port too, ... Determine the ports (pcAnywhere uses 5631 for DATA, 5632 for STATUS, I ...
    (microsoft.public.windowsxp.work_remotely)