RE: When running network setup I get cannot
anonymous_at_discussions.microsoft.com
Date: 07/01/04
- Next message: Lanwench [MVP - Exchange]: "Re: Running batch file from NetWare login script"
- Previous message: anonymous_at_discussions.microsoft.com: "Upgrade to Pro and No More Wireless Access"
- In reply to: Ashleigh: "RE: When running network setup I get cannot"
- Messages sorted by: [ date ] [ thread ]
Date: Thu, 1 Jul 2004 08:03:00 -0700
OK, thank you very much for your help here, looks like I
will get the problem solved, but Im stuck at this line:
Select use DHCP on this page now, click ok
Where is this option? Here is what I see under TCP/IP
and under the advanced tab, where it says DHCP is
enabled. At this point, it still has the IP address
conflict that wont allow me to turn on ICS.
http://img26.photobucket.com/albums/v78/Stunna7516/error.j
pg
>-----Original Message-----
>Easy one this fortunatly, it looks like your network
card that works (lan) has allready go the addres
192.168.0.1 manually assigned to it, however ICS NEEDS
this address to configure itself. Easiest way to solve
this is to change the ip address of the Lan car to
something else. However if the lan card also needs this
address then you can......
>
>view the tcp properties for the lan card (lan /
properties / tcpip) and make a note of them so you can
use them later.
>
>Select use DHCP on this page now, click ok
>
>now enable ICS by going properties / advanced / share my
connection / select the wifi card for the lan adapter,
click ok
>
>ICS will now be installed on that card, go properties,
tcpip for the wifi card, notice how it's setup for
192.168.0.1/255.255.255.0, change this to
192.168.1.1/255.255.255.0 OK out
>
>Slect the lan card and reset the settings.
>
>Now on the computer you want to use the shared
connection with goto the wifi cards properties/tcpip, and
setup it up manually for ip 192.168.1.2/255.255.255.0
with default gateway of 192.168.1.1 and dhcp address of
192.168.1.1 and it should work.
>
>Hope that helps
>
>Ashleigh
>
>"Doom59" wrote:
>
>> My setup is this:
>> CABLE MODEM > NETGEAR WIRELESS ROUTER > PC A WIRELESS
CARD
>> I want my PC A to be able to have internet connection
sharing enabled, using the wireless connection to the
internet to connect another computer with the lan port.
>>
>> In an effort to get internet connection sharing
enabled, I run the home and small office network setup
wizard in XP. Everything is fine until the last screen,
and this pops up where it should say success:
>>
http://img26.photobucket.com/albums/v78/Stunna7516/cannotc
omplete.jpg
>> It doesnt tell me a single thing about the problem.
>>
>> Another thing Ive tried is via network connections
right clicking my wireless connection and turning on ics
under advanced. This is the error I get:
>>
http://img26.photobucket.com/albums/v78/Stunna7516/network
connections.jpg
>> When I enabled it under the lan, it works but I lose
my internet connection, probably because it thinks it
should be coming from the lan or maybe something else.
>>
>> Is there another way to enable ICS between my wireless
card and lan, or figure out why Im getting these two
errors?
>.
>
- Next message: Lanwench [MVP - Exchange]: "Re: Running batch file from NetWare login script"
- Previous message: anonymous_at_discussions.microsoft.com: "Upgrade to Pro and No More Wireless Access"
- In reply to: Ashleigh: "RE: When running network setup I get cannot"
- Messages sorted by: [ date ] [ thread ]
Relevant Pages
|
