Re: S-video tv out

Tech-Archive recommends: Repair Windows Errors & Optimize Windows Performance

Hey Paul, thanks a lot. Yea mine is the non-standard 7-pin. Still the 1st 4
pins should be same as it says in Wiki. Well the problem is Dell didnt
provide the adapter. I have to order now. And thanks for the links. Those are
helpful. I was wondering whether the 21" CRT TV monitor has too low
resolution for 8600 GT, coz when I tried to enable the secodary monitor from
Nvidia the resolution got down to 800x600 with 8bit colors and the tv started
a noise till that secondary monitor was enabled. And the laptop does have a
hotkey for changing monitors, but that says "No external dislay", I aslo
tried with rigorous display detection but it failed.
Thanks again.

"Paul" wrote:

Ingress wrote:
Well the S-video(out) port of my laptop I have hooked my "S-Video to RCA"
connector to, is called a tv-out I guess. I have VGA and HDMI out too, but
not the cables right now. So using s-video which is a 7-pin output not 4-pin.
The manual of my laptop which is a Dell XPS M1530 says to connect using
S-video to component/composite video adapter and from that a RCA to RCA
connector. I guess that is similar with S-video to RCA connector unless you
correct me.

The picture on the web page, shows a minidin with 7 pins and alignment
tab.

http://www.dell.com/content/products/productdetails.aspx/xpsnb_m1530?c=us&cs=22&l=en&s=dfh

It looks to me, like this. (One picture here, is the mirror image
of the other, and it may depend on whether you're looking at the
cable or the computer end, as to which view is right.)

http://en.wikipedia.org/wiki/File:Pseudo_miniDIN-7_Diagram.png

There are more details here, indicating the pinout may not be
standardized. The adapter provided with your Dell computer may be
the best choice.

http://en.wikipedia.org/wiki/Mini-DIN_connector

If you use the software provided with the video interface, you
may be able to see whether one or two "monitors" are present.
Sometimes, on a 75 ohm composite interface, a user has to
select "force detection", when the loading of the TV is
not detected. In this thread, you can see the amount of
floundering you have to do, to get a TV to work. Nvidia has
both the "new" and the "classic" control panel, and the new
one is austere compared to the old one.

http://forums.nvidia.com/lofiversion/index.php?t61279.html

On a laptop, there can be a hot key you can press, to select
the driving of an alternate display (check your manual). Judging
by the description of the computer in your case, there are multiple
output connectors, so I don't know whether using that hot key would
be more useful than using a control panel or not.

Quality wise, HDMI or VGA are higher bandwidth options. Depending
on what the TV supports, either one of those may give better
results. After having tried composite here, I wasn't impressed
with the results.

Paul


"Dragomir Kollaric" wrote:

On 2009-03-29, Ingress hit the keyboard and wrote:
Hi everyone,

I have Nvidia Geforce 8600 GT in my laptop from which I want the display to
a 21 inch CRT Sony Wega TV. I am using the S-Video to RCA connector but I am
getting no signal on the TV at all. I have tried reducing resolution and
colors to the lowest possible. When I enable the secodary monitor the
resolution and color in my laptop gets too bad yet there is no display on the
TV (just a noise). Can you please direct me to the source and possible
solution to this problem? Thanks in advance.
I could be wrong, but would you not need a "TV-out" on the
Video-Card to hook up a TV on the PC? the card I'm using has this
output. What does the manual for the LAPTOP say about hooking up a
TV?

The other question is if the driver still has this option.



Dragomir Kollaric

--
Q: Have you ever heard voices when no one else was there?
A: Yes. From the radio. From the television. From the telephone.
<1234641050_83@xxxxx> as found on alou



.

Relevant Pages

  • Re: Dead Latitude D505
    ... the battery get ... problem is that it does not takes charge from the power adapter. ... Broken power connector on the motherboard is the most likely ... but effective test procedure to make sure laptop motherboards ...
    (alt.sys.pc-clone.dell)
  • Re: "Old Mac" video connector strapping for multi-resolution
    ... > connector, and I've acquired a nice large monitor with a "new style" ... So I need to build an adapter. ... > it so all the possible resolutions will show up in the "monitors" CP. ...
    (comp.sys.mac.hardware.video)
  • Re: Desktop hmm
    ... My Inspiron 1200 has video out, which I take it would only copy the ... onboard screen to the external monitor. ... What jacks to I need on a laptop to drive a randomly good external ... S-Video TV-out connector ...
    (alt.sys.pc-clone.dell)
  • Re: monitor
    ... The monitor is connected to the laptop. ... Most laptops have a VGA out connector. ...
    (microsoft.public.windows.vista.general)
  • Re: no DVI with VAIO in docking station
    ... Another thing I tried is uninstalling the monitor drivers; the monitor then becomes a "Plug-and-Play" type rather than being identified as a Philips 200XW7. ... Note that the current external monitor works fine when connecting it to either laptop or dockingstation with a VGA cable. ... The cable that came with the monitor was already changed for a brand new one; no difference (still I will check pin continuity on the new cable). ... If I wanted a simplistic test, I might try making a "dummy load connector". ...
    (microsoft.public.windowsxp.hardware)