Re: SCSI Cheetah HD not seen in XP

Tech-Archive recommends: Repair Windows Errors & Optimize Windows Performance

Got it....

Downloaded DiscWizard Starter Edition Utility from Seagate....
Made the floppy's...
Botted from floppy's....
Formatted the drive...

Back in business!!!

-K




"KDawg" wrote:

Yves~

Thanks for the quick reply...

The 29160 does show-up in the Device Manager...
The Cheetah does not show-up in Disc Management...

-K




"Yves Leclerc" wrote:

Does the Adaptec 29160 SCSI controller card show up in the Device Manager?

Can you see the Cheetah hard drive in Disk Management? If yes, you may have
to assign a drive letter to or format it in Disk Management.

On 18/10/2006 KDawg <KDawg@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote:
Hey there~

I need a SCSI / XP expert!

In short, my problem is - Windows is not seeing a new Cheetah SCSI drive
installed on an Adaptec 29160 controller.

My system is a Dell 530 Workstation with a couple of Xeon 2.4G chips.
Win XP Pro, SP1
No Internet, etc.... bare bones for Audio Engineering apps...
2 HDs are ATA-100... no problem there...
The 3rd HD is SCSI with a separate controller and that's where my problem
lies...

I'd been using the 29160 controller with an IBM 10K Ultrastar forever, but
the IBM just took a dump... so I replaced it with a Cheetah 10K.7 (Seagate,
73GB, 10K, 68 pin)

Bios sees the set-up as~
SCSI ID 0 Seagate ST373207LW
SCSI ID 7 Adaptec 29160
....same SCSI IDs as before...

The Adaptec card communicates with the Seagate drive in DOS using the
Seagate utility program.... and I can format the drive with (the most
current) Adaptec utility. So, the controller and drive seem to be chatting
OK at low level... I can also see the system acknowledge the card/drive with
a 160 negotiated speed during regular boot-up... so, everything seems cool as
it fires-up...

But, If I boot into plain-jane DOS (not using the Adaptec utulity)... no
drive...
And in Windows... no drive.

The drive is still in it's basic/factory configuration... no pin
changes/etc... seems no need since communication is happening at that
low-level OK (?)

So, I'm really stumped! I've combed through all the manuals,
knowledge-bases, etc., several times. I just can't tell for sure where the
problem lies, but it seems to me it's most likely a Windows issue (?)

Many thanks for any ideas / insight!!
~Cheers~


--
---

Y.


.

Relevant Pages

  • Re: 6.2 Release - Adaptec 2130SLP driver?? issue - aac driver
    ... the controller stopped responding nothing was recorded to my logs. ... I was using the driver released by Adaptec ... just about all scsi devices/card models still in as I continued my ...
    (freebsd-stable)
  • Re: SCSI Cheetah HD not seen in XP
    ... Does the Adaptec 29160 SCSI controller card show up in the Device Manager? ... Can you see the Cheetah hard drive in Disk Management? ... I need a SCSI / XP expert! ...
    (microsoft.public.windowsxp.hardware)
  • Re: SCSI Cheetah HD not seen in XP
    ... Can you see the Cheetah hard drive in Disk Management? ... I need a SCSI / XP expert! ... installed on an Adaptec 29160 controller. ... The 3rd HD is SCSI with a separate controller and that's where my problem ...
    (microsoft.public.windowsxp.hardware)
  • Re: Win2k clean install hangs during reboot
    ... common part numbers for the SCSI controller. ... in controller on the motherboard, says Adaptec AIC-7899G. ... so that I can get the correct drivers for it. ...
    (microsoft.public.win2000.setup)
  • Re: ICP Vortex mit einzelner Platte?
    ... Format der Platte versteht, ... Adaptec eingerichtete Platte am ICP ohne Format einwandfrei genutzt ... Controller, weil der Adaptec sich beharrlich weigerte, eine am Symbios ...
    (de.comp.hardware.laufwerke.festplatten)