Re: Help, accidentaly unistalling Primary IDE Drivers

Tech Tip: Click here to run a free scan for Windows Errors and optimize PC performance


"Behnoud" <Behnoud@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:AC23692F-34E4-4881-A371-3CE1B62EC0D9@xxxxxxxxxxxxxxxx
> dear peterk,
> thanks for searching the net for me,
>
> but these are hyperlinks to intel websites for downloading chipset
> software,
> I already have the latest...
>
> sorry but this is not my problem. As you might know, I got problem with
> primary and secondary IDE channels, those bundled with windows, and there
> is
> no help installing intel chipset software, 'cause there is no driver for
> IDE
> channels inside Intel's package.... so sorry, but this did not help!


If you haven't already dont it, a try at doing a Repair/Install for the XP
CD might help. I can't see that you have anything to loose.

Good luck.

>
> "peterk" wrote:
>
>> Found this on the Intel website
>> http://www.intel.com/support/chipsets/sb/cs-015001.htm
>> as well as this
>> http://www.intel.com/support/chipsets/sb/CS-009241.htm
>> hope it helps
>> peterk
>> --
>> Never trust a computer you can't throw out the window. - Steve Wozniak
>> "Behnoud" <Behnoud@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
>> news:107A6635-05D5-4812-800B-4456F6FC8C25@xxxxxxxxxxxxxxxx
>> > Thanks for your guides!
>> >
>> > But let me make it clear that I know a bit about computer stuff and I
>> > know
>> > how to simply hit the reinstall button on device properties page, :-)
>> >
>> > My problem is just far beyond, when the PNP services or me trying to
>> > reinstall the drivers for any one of IDE Channels (Not controllers!)
>> > the
>> > wizard unexpectedly leaves the process and shows "the driver is not
>> > intended
>> > for this platform" [very important], I should remind, during
>> > reinstalling
>> > process of every IDE Channel the first thing is to install "atapi.sys",
>> > this
>> > is where my system fails to install and leaves the process. this
>> > shoyuld
>> > be
>> > clear enough for you...
>> >
>> > the second thing, I did unistall both 'Intel Ultra-ATA controllers
>> > 82801EB'
>> > (one for IDE and the other for SATA), and restarted my system to
>> > reinstall
>> > them automatically. Both controllers installed and prompted for
>> > restart,
>> > after that it was successful in installing 2 out of 4 IDE channels,
>> > Primary
>> > and IDE on ATA were my windows is installed on Primary [got two HDDs
>> > one
>> > on
>> > IDE primary master theother one on SATA Primary and one CD-RW on IDE
>> > Secondary Master]. the SATA IDE channels did not install. I tried to
>> > unistall
>> > the controller for SATA once more, nothing happened.
>> >
>> > Sorry to repeat once again, but my system won't go through simple
>> > install
>> > process!!
>> >
>> > Thanks again,
>> >
>> > "thedon57" wrote:
>> >
>> >>
>> >> Behnoud wrote:
>> >> > *Please Help!
>> >> >
>> >> > I did unistall the 2 Primary IDE Drivers (IDE0 and SATA0), I wnated
>> >> > to get
>> >> > out of conflice between my IDE Controllers and my Onboard Sound
>> >> > Device.
>> >> > ""Gigabyte 8IG1000Pro-G rev1.2 motherboard with 865G Intel Chipset
>> >> > supporting
>> >> > AC'97 Audio from Realtek Onboard"" this is My configuration.
>> >> > Sometime
>> >> > in the
>> >> > past, I'd been hearing sound problems when trying to burn CD's or
>> >> > Copy
>> >> > contents to Harddrive, I unistalled the Secondary IDE and
>> >> > Reinstalled
>> >> > (it was
>> >> > very hard to reistall!) and the problem was gone. Now. I have the
>> >> > same
>> >> > Problem with My Harddrives, so I did Unistall both primary IDEs and
>> >> > I
>> >> > cannot
>> >> > install them anymore. It says: "Code 28 - the driver is not intended
>> >> > for the
>> >> > platform" and the driver remains as IDE Channel with a yellow
>> >> > exclamation
>> >> > mark.
>> >> >
>> >> > Does anybody know what should I do now? I cannot remember the
>> >> > process
>> >> > of
>> >> > installing the Secondary IDE now. It got a trick I think...
>> >> >
>> >> > Thanks *
>> >>
>> >> Hi make your secondary IDE the slave and connect it to the other
>> >> socket
>> >> on the ribbon.
>> >>
>> >> Now the computer when you start it up shoul find it.
>> >>
>> >> If you still get the code 28 this is what it means The drivers for
>> >> this
>> >> device are not installed.
>> >>
>> >> Goto device manager and click on the yellow mark this should install
>> >> the driver for that IDE, if it does not then download a compatible
>> >> driver for the device, click the Update Driver button and follow the
>> >> wizards prompts to install the new driver.
>> >>
>> >> Hope this helps you.
>> >>
>> >>
>> >>
>> >> --
>> >> thedon57
>> >> ------------------------------------------------------------------------
>> >> Posted via http://www.mcse.ms
>> >> ------------------------------------------------------------------------
>> >> View this thread: http://www.mcse.ms/message1817704.html
>> >>
>> >>
>>
>>
>>


.

Quantcast