Re: USB port
anonymous_at_discussions.microsoft.com
Date: 10/02/04
- Next message: Dee in DC: "Re: motherboard isn't being recognized"
- Previous message: Vince: "cannot install ATI 9600 display driver"
- In reply to: Jim Macklin: "Re: USB port"
- Messages sorted by: [ date ] [ thread ]
Date: Sat, 2 Oct 2004 01:29:25 -0700
have done all this and no joy.....
>-----Original Message-----
>Delete the USB device that has the problem (you do this
in
>device manager). hen you reboot it will be detected and
the
>correct drivers installed. It may be necessary to
delete
>ALL the USB devices, ports and hubs and reboot to get a
>clean driver install.
>
>
>--
>The people think the Constitution protects their rights;
>But government sees it as an obstacle to be overcome.
>
>
><anonymous@discussions.microsoft.com> wrote in message
>news:207501c4a799$9f18e420$a401280a@phx.gbl...
>| Have updated using your instructions.....thank you.
>| However the problem is still there with my printer.
The
>| printer shows in the Device manager as an image device
>| and shows no conflicts. Below that the USB device does
>| show a conflict and no matter where i look i cannot
seem
>| to find the right driver for. although system32 will
>| show as being avaiable, but still no driver is found,
and
>| I get a message saying that the device is not properly
>| installed. In the past I have had to re-format and re-
>| load winxp to get the thing to work ....????
>| >-----Original Message-----
>| >Be sure to follow the instruction, which should be on
>| the
>| >download page for the BIOS update. In general there
are
>| two
>| >types of updates, one must be run on a cold boot
using a
>| >floppy disk with a DOS bootable and the BIOS update on
>| the
>| >disk. If the BIOS was a zip file, it must be
extracted
>| and
>| >copied to the floppy.
>| >The other, newer type is an exe file that will update
>| the
>| >BIOS while Windows is running.
>| >
>| >
>| ><anonymous@discussions.microsoft.com> wrote in message
>| >news:134901c4a6b7$27519320$a401280a@phx.gbl...
>| >| Thanx ..I will try your suggestion. The motherboard
>| is a
>| >| gigabyte and using the serial numbe I have tracked
down
>| >| the update, however when I try to flash the Bios it
>| tells
>| >| me that "the bios" is not supported. I will follow
>| your
>| >| instructions and report back....thank you
>| >| >-----Original Message-----
>| >| >The BIOS and other mobo drivers are available from
the
>| >| mobo
>| >| >mfg'rs website. Since the USB is built-in, that is
>| the
>| >| best
>| >| >place to start. Get EVEREST from www.lavalys.com
to
>| >| >determine the exact mobo by make/model and serial
>| >| number.
>| >| >It will also report the BIOS and details of the
>| drivers
>| >| >installed.
>| >| >
>| >| >Get a UPS (battery backed power supply) so you will
>| have
>| >| >reliable power. Then update the BIOS and drivers.
>| The
>| >| sure
>| >| >that the properties for the USB is set to supply
power
>| >| and
>| >| >not time out.
>| >| >
>| >| >
>| >| >--
>| >| >The people think the Constitution protects their
>| rights;
>| >| >But government sees it as an obstacle to be
overcome.
>| >| >
>| >| >
>| >| ><anonymous@discussions.microsoft.com> wrote in
message
>| >| >news:09d701c4a620$c3d58090$a401280a@phx.gbl...
>| >| >| The port is built in..and i haven't updated the
>| >| bios..had
>| >| >| spme problems trying to do some time ago
>| >| >| >-----Original Message-----
>| >| >| >Is it a port built into the mobo or a PCI card
in a
>| >| >| slot?
>| >| >| >Perhaps it isn't an XP problem, but a hardware
>| problem
>| >| >| with
>| >| >| >your mobo? Have you updated the BIOS?
>| >| >| >
>| >| >| >
>| >| >| >--
>| >| >| >The people think the Constitution protects their
>| >| rights;
>| >| >| >But government sees it as an obstacle to be
>| overcome.
>| >| >| >
>| >| >| >
>| >| >| >"Michael Alexander"
>| >| >| <anonymous@discussions.microsoft.com>
>| >| >| >wrote in message
>| >| >| >news:136d01c4a5f9$4f44df90$a601280a@phx.gbl...
>| >| >| >| Using Win XP pro. Have connected via USB
port a
>| >| >| >| printer, every time I use that same port for
my
>| >| webcam,
>| >| >| >| the scanner part of my printer will not owrk
>| >| properly
>| >| >| >| until I remove and re-load XP. Have
downloaded
>| the
>| >| >| >| latest software from printer site
(lexamrk...with
>| >| >| patch)
>| >| >| >| but still cannot get proper connection.
>| >| >| >|
>| >| >| >| If I re-format and load XP..it will be ok
until I
>| >| use
>| >| >| >| that USB port again...any help appreciated
>| >| >| >
>| >| >| >
>| >| >| >.
>| >| >| >
>| >| >
>| >| >
>| >| >.
>| >| >
>| >
>| >
>| >.
>| >
>
>
>.
>
- Next message: Dee in DC: "Re: motherboard isn't being recognized"
- Previous message: Vince: "cannot install ATI 9600 display driver"
- In reply to: Jim Macklin: "Re: USB port"
- Messages sorted by: [ date ] [ thread ]
Relevant Pages
|
