Re: HOPING for HELP !!!!!!!!!!!!!!!!!!!!!!!

Tech Tip: Click here to run a free scan for Windows Errors and optimize PC performance

From: sogs (nospamrobertv1_at_comcast.net)
Date: 02/16/04

Next message: DBF: "Re: Pioneer 107 DVD RW"
Previous message: Jim Macklin: "Re: firewire"
In reply to: Peter: "RE: HOPING for HELP !!!!!!!!!!!!!!!!!!!!!!!"
Next in thread: sogs: "Re: HOPING for HELP !!!!!!!!!!!!!!!!!!!!!!!"
Messages sorted by: [ date ] [ thread ]

Date: Mon, 16 Feb 2004 14:37:19 GMT

On Mon, 16 Feb 2004 03:21:07 -0800, "Peter"
<anonymous@discussions.microsoft.com> wrote:

>Hi,
>
>Before I use broadband modem, I also use US Robotic 56K modem. I could connect it to either Com1 or Com2 and XP imediately recongzied it and load the native drivers without any problem and it worked fine.
>I'm now just using it for WinFax only.
>Have you installed SP1 or SP1a?
>If not yet, install it from windows update site.

I can't install an update if I can't use the modem.

>Try boot in safe mode and login as administrator, go to device manager and uninstall the modem then shut down the machine.
>Disconnect the modem and power on the PC. Boot into BIOS and load the default settings then save and exit.
>After windows startup, reconnect the modem to Com1 or Com2.
>Power on the modem and windows should find it and load the drivers.

I will try this and if nothing happens I'm going to reinstall XP.

>If nothing can resolve your problem, try update the mobo BIOS.

Can't get online without the modem.

>Hope it helps.
>
>Peter
>
>
> ----- sogs wrote: -----
>
> I picked up Pentium III 450 mhz with Xp installed. When I booted it
> up I got the following message: "1151- Serial port A address conflict
> detected". Not knowing what this really meant, I took a modem "US
> Robotics 56K" and installed it in this machine and it does not
> recognize the modem. I went into the setup and changed the Serial A &
> B (addresses?). I got the error code 1151 to go away but the system
> still does not recognize the modem. If I query the modem it says it
> does not detect a modem. Everything in Device manager is listed as
> working ok. These 2 setup's for the Serial A & B gave me the error
> message:
> Serial A 2F8 - 2FF IRQ 4
> Serial B 3F8 - 3FF IRQ 3
>
> or
>
> Serial A 2E8 - 2EF IRQ 4
> Serial B 3F8 - 3FF IRQ 3
>
> If I change the above to any of the other combinations the error code
> goes away. I have listed below the system information that is
> probably pertinent to this problem. Yes, the modem does work fine in
> another machine. Maybe all I need to do is reinstall Windows? I have
> XP, ME, & 98 available. All help is GREATLY appreciated !!!!!
>
> Here's The Sytem Info for I/O, IRQ, Modem, Conflicts/Sharing,
> Protocol, & Winsock:
>
>
> [I/O]
>
> Resource Device Status
> 0x00000000-0x00000CF7 PCI bus OK
> 0x00000000-0x00000CF7 Direct memory access controller OK
> 0x00000D00-0x0000FFFF PCI bus OK
> 0x000003B0-0x000003BB Intel 82443BX Pentium(r) II Processor to AGP
> Controller OK
> 0x000003B0-0x000003BB Matrox Graphics Millennium G200 AGP OK
> 0x000003C0-0x000003DF Intel 82443BX Pentium(r) II Processor to AGP
> Controller OK
> 0x000003C0-0x000003DF Matrox Graphics Millennium G200 AGP OK
> 0x00000A79-0x00000A79 ISAPNP Read Data Port OK
> 0x00000279-0x00000279 ISAPNP Read Data Port OK
> 0x00000274-0x00000277 ISAPNP Read Data Port OK
> 0x000000F0-0x000000FF Numeric data processor OK
> 0x00000020-0x0000003F Programmable interrupt controller OK
> 0x000000A0-0x000000BF Programmable interrupt controller OK
> 0x00000040-0x00000043 System timer OK
> 0x00000080-0x0000008F Direct memory access controller OK
> 0x000000C0-0x000000DF Direct memory access controller OK
> 0x00000070-0x00000071 System CMOS/real time clock OK
> 0x00000061-0x00000061 System speaker OK
> 0x00000060-0x00000060 Standard 101/102-Key or Microsoft Natural PS/2
> Keyboard OK
> 0x00000064-0x00000064 Standard 101/102-Key or Microsoft Natural PS/2
> Keyboard OK
> 0x00000378-0x0000037F ECP Printer Port (LPT1) OK
> 0x00000778-0x0000077D ECP Printer Port (LPT1) OK
> 0x000002E8-0x000002EF Communications Port (COM1) OK
> 0x000003E8-0x000003EF Communications Port (COM2) OK
> 0x000003F0-0x000003F5 Standard floppy disk controller OK
> 0x000003F7-0x000003F7 Standard floppy disk controller OK
> 0x00000220-0x0000022F ES1869 Plug and Play AudioDrive (WDM) OK
> 0x00000388-0x0000038B ES1869 Plug and Play AudioDrive (WDM) OK
> 0x00000330-0x00000331 ES1869 Plug and Play AudioDrive (WDM) OK
> 0x00000800-0x00000807 ES1869 Control Interface (WDM) OK
> 0x00001060-0x0000106F Intel(r) 82371AB/EB PCI Bus Master IDE
> Controller OK
> 0x000001F0-0x000001F7 Primary IDE Channel OK
> 0x000003F6-0x000003F6 Primary IDE Channel OK
> 0x00000170-0x00000177 Secondary IDE Channel OK
> 0x00000376-0x00000376 Secondary IDE Channel OK
> 0x00001040-0x0000105F Intel(r) 82371AB/EB PCI to USB Universal Host
> Controller OK
> 0x00000010-0x0000001F Motherboard resources OK
> 0x00000050-0x00000052 Motherboard resources OK
> 0x00000072-0x00000073 Motherboard resources OK
> 0x00000076-0x00000077 Motherboard resources OK
> 0x00000078-0x0000007F Motherboard resources OK
> 0x00000090-0x0000009F Motherboard resources OK
> 0x000000EC-0x000000EF Motherboard resources OK
> 0x0000015C-0x0000015D Motherboard resources OK
> 0x00000260-0x00000261 Motherboard resources OK
> 0x000004D0-0x000004D1 Motherboard resources OK
> 0x0000077E-0x0000077F Motherboard resources OK
> 0x0000F800-0x0000F81F Motherboard resources OK
> 0x0000F820-0x0000F83F Motherboard resources OK
> 0x0000FC00-0x0000FC1F Motherboard resources OK
>
>
> [IRQs]
>
> Resource Device Status
> IRQ 9 Microsoft ACPI-Compliant System OK
> IRQ 11 Matrox Graphics Millennium G200 AGP OK
> IRQ 13 Numeric data processor OK
> IRQ 0 System timer OK
> IRQ 8 System CMOS/real time clock OK
> IRQ 12 PS/2 Compatible Mouse OK
> IRQ 1 Standard 101/102-Key or Microsoft Natural PS/2 Keyboard OK
> IRQ 3 Communications Port (COM1) OK
> IRQ 4 Communications Port (COM2) OK
> IRQ 6 Standard floppy disk controller OK
> IRQ 5 ES1869 Plug and Play AudioDrive (WDM) OK
> IRQ 14 Primary IDE Channel OK
> IRQ 15 Secondary IDE Channel OK
> IRQ 10 Intel(r) 82371AB/EB PCI to USB Universal Host Controller
> OK
>
>
> [Modem]
>
> Item Value
> Name Standard 56000 bps Modem
> Description Standard 56000 bps Modem
> Device ID ROOT\MODEM\0001
> Device Type External Modem
> Attached To COM1
> Answer Mode Not Available
> PNP Device ID ROOT\MODEM\0001
> Provider Name Microsoft
> Modem INF Path mdmgen.inf
> Modem INF Section Gen556F
> Blind Off X4
> Blind On X3
> Compression Off %C
> Compression On %C3
> Error Control Forced \N2
> Error Control Off \N
> Error Control On \N3
> Flow Control Hard &K3
> Flow Control Off &K
> Flow Control Soft &K4
> DCB 
> Default <
> Inactivity Timeout 0
> Modulation Bell B1
> Modulation CCITT B
> Prefix AT
> Pulse P
> Reset AT&F<cr>
> Responses Key Name Standard 56000 bps Modem::(Standard Modem
> Types)::Microsoft
> Speaker Mode Dial M1
> Speaker Mode Off M0
> Speaker Mode On M2
> Speaker Mode Setup M3
> Speaker Volume High L3
> Speaker Volume Low L0
> Speaker Volume Med L2
> String Format Not Available
> Terminator <cr>
> Tone T
>
> Name U.S. Robotics 56K FAX INT
> Description U.S. Robotics 56K FAX INT
> Device ID ROOT\MODEM\0002
> Device Type Internal Modem
> Attached To COM1
> Answer Mode Not Available
> PNP Device ID ROOT\MODEM\0002
> Provider Name 3Com
> Modem INF Path oem2.inf
> Modem INF Section ModemFIn31
> Blind Off X4
> Blind On X3
> Compression Off &K0
> Compression On &K1
> Error Control Forced &M5
> Error Control Off &M0
> Error Control On &M4
> Flow Control Hard &H1&R2&I0
> Flow Control Off &H0&I0&R1
> Flow Control Soft &H2&I2&R1
> DCB 
> Default <
> Inactivity Timeout 0
> Modulation Bell B1
> Modulation CCITT B0
> Prefix AT
> Pulse P
> Reset AT&F1<cr>
> Responses Key Name U.S. Robotics 56K FAX INT::3Com::3Com
> Speaker Mode Dial M1
> Speaker Mode Off M0
> Speaker Mode On M2
> Speaker Mode Setup M3
> Speaker Volume High L3
> Speaker Volume Low L0
> Speaker Volume Med L2
> String Format Not Available
> Terminator <cr>
> Tone T
>
>
> [Conflicts/Sharing]
>
> Resource Device
> I/O Port 0x00000000-0x00000CF7 PCI bus
> I/O Port 0x00000000-0x00000CF7 Direct memory access controller
>
> I/O Port 0x000003C0-0x000003DF Intel 82443BX Pentium(r) II Processor
> to AGP Controller
> I/O Port 0x000003C0-0x000003DF Matrox Graphics Millennium G200 AGP
>
> Memory Address 0x41000000-0x41FFFFFF Intel 82443BX Pentium(r) II
> Processor to AGP Controller
> Memory Address 0x41000000-0x41FFFFFF Matrox Graphics Millennium
> G200 AGP
>
> Memory Address 0x40000000-0x408FFFFF Intel 82443BX Pentium(r) II
> Processor to AGP Controller
> Memory Address 0x40000000-0x408FFFFF Matrox Graphics Millennium
> G200 AGP
>
> Memory Address 0xA0000-0xBFFFF PCI bus
> Memory Address 0xA0000-0xBFFFF Intel 82443BX Pentium(r) II Processor
> to AGP Controller
> Memory Address 0xA0000-0xBFFFF Matrox Graphics Millennium G200 AGP
>
> I/O Port 0x000003B0-0x000003BB Intel 82443BX Pentium(r) II Processor
> to AGP Controller
> I/O Port 0x000003B0-0x000003BB Matrox Graphics Millennium G200 AGP
>
>
> [Serial]
>
> Item Value
> Name Communications Port (COM1)
> Status OK
> PNP Device ID ACPI\PNP0501\1
> Maximum Input Buffer Size 0
> Maximum Output Buffer Size No
> Settable Baud Rate Yes
> Settable Data Bits Yes
> Settable Flow Control Yes
> Settable Parity Yes
> Settable Parity Check Yes
> Settable Stop Bits Yes
> Settable RLSD Yes
> Supports RLSD Yes
> Supports 16 Bit Mode No
> Supports Special Characters No
> Baud Rate 9600
> Bits/Byte 8
> Stop Bits 1
> Parity None
> Busy No
> Abort Read/Write on Error No
> Binary Mode Enabled Yes
> Continue XMit on XOff No
> CTS Outflow Control No
> Discard NULL Bytes No
> DSR Outflow Control 0
> DSR Sensitivity 0
> DTR Flow Control Type Enable
> EOF Character 0
> Error Replace Character 0
> Error Replacement Enabled No
> Event Character 0
> Parity Check Enabled No
> RTS Flow Control Type Enable
> XOff Character 19
> XOffXMit Threshold 512
> XOn Character 17
> XOnXMit Threshold 2048
> XOnXOff InFlow Control 0
> XOnXOff OutFlow Control 0
> IRQ Channel IRQ 3
> I/O Port 0x000002E8-0x000002EF
> Driver c:\windows\system32\drivers\serial.sys (5.1.2600.0
> (XPClient.010817-1148), 61.00 KB (62,464 bytes), 8/23/2001 8:00 AM)
>
> Name Communications Port (COM2)
> Status OK
> PNP Device ID ACPI\PNP0501\2
> Maximum Input Buffer Size 0
> Maximum Output Buffer Size No
> Settable Baud Rate Yes
> Settable Data Bits Yes
> Settable Flow Control Yes
> Settable Parity Yes
> Settable Parity Check Yes
> Settable Stop Bits Yes
> Settable RLSD Yes
> Supports RLSD Yes
> Supports 16 Bit Mode No
> Supports Special Characters No
> Baud Rate 9600
> Bits/Byte 8
> Stop Bits 1
> Parity None
> Busy No
> Abort Read/Write on Error No
> Binary Mode Enabled Yes
> Continue XMit on XOff No
> CTS Outflow Control No
> Discard NULL Bytes No
> DSR Outflow Control 0
> DSR Sensitivity 0
> DTR Flow Control Type Enable
> EOF Character 0
> Error Replace Character 0
> Error Replacement Enabled No
> Event Character 0
> Parity Check Enabled No
> RTS Flow Control Type Enable
> XOff Character 19
> XOffXMit Threshold 512
> XOn Character 17
> XOnXMit Threshold 2048
> XOnXOff InFlow Control 0
> XOnXOff OutFlow Control 0
> IRQ Channel IRQ 4
> I/O Port 0x000003E8-0x000003EF
> Driver c:\windows\system32\drivers\serial.sys (5.1.2600.0
> (XPClient.010817-1148), 61.00 KB (62,464 bytes), 8/23/2001 8:00 AM)
>
>
> [Protocol]
>
> Item Value
> Name MSAFD Tcpip [TCP/IP]
> Connectionless Service No
> Guarantees Delivery Yes
> Guarantees Sequencing Yes
> Maximum Address Size 16 bytes
> Maximum Message Size 0 bytes
> Message Oriented No
> Minimum Address Size 16 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting No
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data Yes
> Supports Graceful Closing Yes
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
> Name MSAFD Tcpip [UDP/IP]
> Connectionless Service Yes
> Guarantees Delivery No
> Guarantees Sequencing No
> Maximum Address Size 16 bytes
> Maximum Message Size 63.93 KB (65,467 bytes)
> Message Oriented Yes
> Minimum Address Size 16 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting Yes
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting Yes
>
> Name RSVP UDP Service Provider
> Connectionless Service Yes
> Guarantees Delivery No
> Guarantees Sequencing No
> Maximum Address Size 16 bytes
> Maximum Message Size 63.93 KB (65,467 bytes)
> Message Oriented Yes
> Minimum Address Size 16 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting Yes
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption Yes
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting Yes
>
> Name RSVP TCP Service Provider
> Connectionless Service No
> Guarantees Delivery Yes
> Guarantees Sequencing Yes
> Maximum Address Size 16 bytes
> Maximum Message Size 0 bytes
> Message Oriented No
> Minimum Address Size 16 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting No
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption Yes
> Supports Expedited Data Yes
> Supports Graceful Closing Yes
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{593BDD4A-CCA6-4668-953A-87FD9F51FB65}] SEQPACKET
> 4
> Connectionless Service No
> Guarantees Delivery Yes
> Guarantees Sequencing Yes
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting No
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{593BDD4A-CCA6-4668-953A-87FD9F51FB65}] DATAGRAM
> 4
> Connectionless Service Yes
> Guarantees Delivery No
> Guarantees Sequencing No
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting Yes
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{1CF9329A-E000-4832-BF5E-4D8E381D0F8E}] SEQPACKET
> 3
> Connectionless Service No
> Guarantees Delivery Yes
> Guarantees Sequencing Yes
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting No
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{1CF9329A-E000-4832-BF5E-4D8E381D0F8E}] DATAGRAM
> 3
> Connectionless Service Yes
> Guarantees Delivery No
> Guarantees Sequencing No
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting Yes
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{21BCC109-3592-449D-AD68-784AC4B7F13D}] SEQPACKET
> 0
> Connectionless Service No
> Guarantees Delivery Yes
> Guarantees Sequencing Yes
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting No
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{21BCC109-3592-449D-AD68-784AC4B7F13D}] DATAGRAM
> 0
> Connectionless Service Yes
> Guarantees Delivery No
> Guarantees Sequencing No
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting Yes
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{2DD3DB89-B972-4BEC-813F-686D8CB8D6CE}] SEQPACKET
> 1
> Connectionless Service No
> Guarantees Delivery Yes
> Guarantees Sequencing Yes
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting No
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{2DD3DB89-B972-4BEC-813F-686D8CB8D6CE}] DATAGRAM
> 1
> Connectionless Service Yes
> Guarantees Delivery No
> Guarantees Sequencing No
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting Yes
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{CD614656-2310-4CCE-B95F-8D7F50271DE4}] SEQPACKET
> 2
> Connectionless Service No
> Guarantees Delivery Yes
> Guarantees Sequencing Yes
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting No
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
> Name MSAFD NetBIOS
> [\Device\NetBT_Tcpip_{CD614656-2310-4CCE-B95F-8D7F50271DE4}] DATAGRAM
> 2
> Connectionless Service Yes
> Guarantees Delivery No
> Guarantees Sequencing No
> Maximum Address Size 20 bytes
> Maximum Message Size 62.50 KB (64,000 bytes)
> Message Oriented Yes
> Minimum Address Size 20 bytes
> Pseudo Stream Oriented No
> Supports Broadcasting Yes
> Supports Connect Data No
> Supports Disconnect Data No
> Supports Encryption No
> Supports Expedited Data No
> Supports Graceful Closing No
> Supports Guaranteed Bandwidth No
> Supports Multicasting No
>
>
> [WinSock]
>
> Item Value
> File c:\windows\system32\winsock.dll
> Size 2.80 KB (2,864 bytes)
> Version 3.10
>
> File c:\windows\system32\wsock32.dll
> Size 21.00 KB (21,504 bytes)
> Version 5.1.2600.0 (xpclient.010817-1148)
>
>

Next message: DBF: "Re: Pioneer 107 DVD RW"
Previous message: Jim Macklin: "Re: firewire"
In reply to: Peter: "RE: HOPING for HELP !!!!!!!!!!!!!!!!!!!!!!!"
Next in thread: sogs: "Re: HOPING for HELP !!!!!!!!!!!!!!!!!!!!!!!"
Messages sorted by: [ date ] [ thread ]

Relevant Pages

RE: HOPING for HELP !!!!!!!!!!!!!!!!!!!!!!!
... install it from windows update site. ... Try boot in safe mode and login as administrator, go to device manager and uninstall the modem then shut down the machine. ... After windows startup, reconnect the modem to Com1 or Com2. ... Processor to AGP Controller ...
(microsoft.public.windowsxp.hardware)
Re: installing windows
... Windows help - www.rickrogers.org ... > Controller" and the modem. ... Install them one at a time. ...
(microsoft.public.windowsxp.general)
Re: Fax Services Install
... Windows XP Fax has proven to be incompatible with many common ... Modem incompatibility is not apparent ... on the Windows XP Hardware Compatibility List and using the latest drivers. ... >I have uninstalled WinFax and it still will not install the Windows Faxing ...
(microsoft.public.windowsxp.print_fax)
Re: Probedis.exe DLL Initialization Failed Error
... Try a different modem, some are problematic with an OS and a real PITA to get up and running. ... Here is direct link to the driver. ... Double-click the file in Windows Explorer. ... Select Install from a list or specific location. ...
(microsoft.public.windowsxp.general)
Re: Adding a FAX
... There is a FAX program that came with the modem. ... I have a brand new system with Windows ... > Also, I tried to install 'Additional Windows Components', and select FAX. ... > MCE that did not have SP2, and installed it from a separate SP2 CD. ...
(microsoft.public.windowsxp.basics)