Re: BIOS setup utility locks up

Tech-Archive recommends: Repair Windows Errors & Optimize Windows Performance

kleefarr wrote:

"SC Tom" wrote:

"kleefarr" <kleefarr@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message news:3BF1864C-7602-4F4E-9F29-FD3B5BA9E32B@xxxxxxxxxxxxxxxx

"SC Tom" wrote:

"kleefarr" <kleefarr@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:58EAF93A-3E98-4F90-AAAA-8E21DD71D02F@xxxxxxxxxxxxxxxx

"kleefarr" wrote:

I'm having a look at a Win XP Asus P5S800-VM computer for a friend which
he
said stopped working. He said it has power but nothing else, check the
monitor was working by trying it on another PC.

I unplugged the HDD and the DVDRW. I entered BIOS setup and after about
30
seconds it locks up. On starting I get Wrong date/time errors and also an
error saying that the CPU overclock failed. I have tried this a couple of
times after clearing the CMOS backup each time, but I still get a lock up
on
the BIOS setup screen, normally while trying to correct the BIOS
time/date.

Would this indicate a screwed Motherboard?

I forgot to add..

Had already checked the CMOs battery and connections. Voltage was 2.85v
but
changed for a new one anyway. 3.08v.

I had a look at the online manual about overclocking, but there was no
indication of any specific jumper settings for enabling overclocking.

I have also checked the Intrusion/case open jumper and that seems fine.

I have run a voltage test..

Purple - 5.02v
Green - 0.16v
Grey - 0.97v (Low)
Orange - 3.28v
Red - 5.21v
Yellow - (When off 0.15v) Power on 11.15. (seems low)
Under Advanced, JumperFree Configuration in BIOS is the AI Overclock Tuner.
Make sure that is set to standard. According to the manual, there is no need
to clear the RTC RAM due to overclocking- it should reset itself after doing
a shutdown and reboot. Make sure your CPU fan is clean and running. You can
check your board temps and voltages in BIOS under Power, Hardware Monitor.

SC Tom


Have changed the PSU and voltage on the 12v rail seemed better, 11.97v.
The fan is working and is now reasonably clean.
I navigated to the 'monitor hardware' section in BIOS and watched for a few
minutes. Fan speed was on auto. CPU temperature climbed to 61.5 oC and the
motherboard temp stayed around the 27/28 oC mark. Then it locked up again.

Motherboard or CPU?

Depending on the model of CPU, that may or may not be high. My AMD in my desktop never gets that high, but my Intel in my notebook will sometimes get that high on intense programs, but drop right back down.
I haven't seen any mention of you changing out the RAM. Have you tried any different RAM in it to see if that changes anything? If you have two or more sticks, you could try them one at a time and see if that solves it. May be a bad stick in there.
Are you using a USB keyboard or PS2? I'd go with a PS2 until the problem is solved- just one more bus to eliminate. Since you don't have a HDD in it at the moment, unplug the mouse, too.
Ain't troubleshooting fun :-)?

SC Tom


Yeah, great fun 8).

I'll have a look and see if I have som RAM that'll fit. I am thinking CPU though.
Mouse is not plugged in, only keyboard.
Will check out the specs from the website a bit later.
Watching Spanish Grand Prix now then it'll be time for Arsenal v Chelsea.

P5S800-VM (Intel, LGA775)

http://c1.neweggimages.com/NeweggImage/productimage/13-131-521-02.jpg

If the CPU temp is 61C and climbing, while sitting in the BIOS, I would
check the CPU cooler. Make sure the fan is spinning at a decent rate.
Check the "push pins" to see if they're secure. Sometimes, a pin or two
will release, leaving the heatsink just hanging there. At the 5 minute
mark of this movie, you can see how the push pins are rotated, before
pulling up on them. Some pins don't handle repeated actuation that
well. If the pins are ruined, you can get an aftermarket cooler.

(Intel LGA775 movie)
http://cache-www.intel.com/cd/00/00/24/12/241209_241209.wmv

This is what I'm using on my LGA775 board. This item bolts to the
motherboard, and is a colossal pain to install. (You have to
pull the motherboard, to fit it.) But it also cannot come loose.

http://www.newegg.com/Product/Product.aspx?Item=N82E16835103046

The plate in the upper right of this picture, goes underneath
the motherboard. A hex nut is placed in the four corners. The
nuts hold the heatsink to the processor. No wimpy plastic pin
to release and let go...

http://c1.neweggimages.com/NeweggImage/productimage/35-103-046-08.jpg

When changing the heatsink, fresh thermal paste should be applied.

(Cleaner kit - if you don't want to buy this, use isopropyl alcohol)
http://www.newegg.com/Product/Product.aspx?Item=N82E16835100010

(Replacement thermal paste)
http://www.newegg.com/Product/Product.aspx?Item=N82E16835100007

HTH,
Paul
.

Relevant Pages

  • Re: SmallC
    ... ;) The old machine is an AWARD BIOS. ... I disabled all bootable devices except the floppy. ... I purchased the motherboard and cpu far in advance of when I intended to use ...
    (alt.lang.asm)
  • Re: [Problem]Can I Use same boot disk in different MOBO same model?
    ... original Boot Disk and If all else failed. ... But Now I find that I would have to upgrade my BIOS for the CPU I ... If you use the same motherboard model, plug the hard drive into the same port ...
    (alt.comp.periphs.mainboard.asus)
  • Re: PII vs PIII
    ... VID pins in the socket (with CPU removed), ... Then there's the BIOS support... ... I think the motherboard has the 440BX ...
    (comp.os.linux.hardware)
  • Re: Starting up is a non-starter.
    ... Pins 1-2 are shorted for normal ... > BIOS back to it's neutral settings. ... > the motherboard Vendor/Model. ... >> it would beep, ...
    (microsoft.public.windowsxp.general)
  • Re: BIOS setup utility locks up
    ... "SC Tom" wrote: ... the BIOS setup screen, normally while trying to correct the BIOS ... Make sure your CPU fan is clean and running. ... Check the "push pins" to see if they're secure. ...
    (microsoft.public.windowsxp.general)