Re: xcopy access denied

On May 3, 2:46 pm, Logie Bear <LogieB...@xxxxxxxxxxxxxxxxxxxxxxxxx>
wrote:
Well I tried rejoining the machine on to the domain and still no joy -
exactly the same error.
I GIVE UP!!!

"Logie Bear" wrote:
Ok, thanks for your help. Maybe I will try and rejoin the PC to the domain
see if that helps.

"Pegasus (MVP)" wrote:

The error messages you report suggest that the PC
cannot locate the share \\Server\Users. You need to
go back to basics and check if
- you can ping the server
- you can ping any other machine
- you can connect to a share on some other machine
- there is a firewall somewhere that blocks you
- there is a malfunctioning network adapter (rare but can happen)
- your spelling of the server/share name is correct

If things worked on this machine before and if they don't work
now then you need to think about what happened in between.
You should also try the WinXP System Restore facility to go
back to a point before things went bad.

If this does not help and if you're convinced that the machine
is not affected by malware or by a virus then uninstalling and
reinstalling all network components might help.

"Logie Bear" <LogieB...@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:8F78E537-4F6F-44AD-A738-13721ACF1641@xxxxxxxxxxxxxxxx
Sorry I missed that bit. Yes the share permissions are correct. As I said
previously I have done this on another twenty or so PC's (including some
yesterday) and it works fine. As for the commands you asked me to try the
results are as follows:
1. Invalid drive specification. 0 file(s) copied
2. The network path was not found
3. Invalid drive specification. 0 file(s) copied

"Pegasus (MVP)" wrote:

Getting a little further. Please try this:
1. Click Start / Run / cmd {OK}
2. Type these commands and report the results.
xcopy /y /h c:\nt*.* "\\Server\users\dawns\My Documents\"{Enter}
ren "\\Server1\users\dawns\My Documents" "My Docs"{Enter}
xcopy /y /h c:\nt*.* "\\Server\users\dawns\My Documents\"{Enter}

In my previous reply I wrote this:
===================
As a separate question: Did you make sure that the
"Share" permissions (as opposed to the NTFS permissions)
of \\Server01\users are set to "Full access" for everyone?
===================

You never replied to this question. It is very important that you do.

"Logie Bear" <LogieB...@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:9FF9E055-D503-42AC-A18C-023F297576B4@xxxxxxxxxxxxxxxx
This is the extract:

Access denied
Unable to create directory - \\Server01\users\dawns\My Documents
0 File(s) copied

Exactly what I get when I run my version.

"Pegasus (MVP)" wrote:

Unfortunately you left out the most important bit in your
test - the redirection of the xcopy screen output. The following
line, taken from my previous reply, is supposted to be one
single long line, even though it may wrap around in your
newsreader.

I suggest you repeat the whole test.

xcopy /s /e /y /c "%UserProfile%\My Documents"
"\\Server01\users\%UserName%\My Documents\"
1>c:\test.txt 2>&1

"Logie Bear" <LogieB...@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:38B7BD26-78BB-4C02-8713-B626C2E78372@xxxxxxxxxxxxxxxx
I tried that one and the files scrolled up the screen with a
message
at
the
end saying it copied 30 files. However, when I went in to check
the
destination directory it had not copied as I modified one of the
files
before
I run it and the last amended date had not changed. The contents
of
the
test.txt file is:

USERDNSDOMAIN=LBS-HQ.LOCAL
USERDOMAIN=LBS-HQ
USERNAME=dawns
USERPROFILE=C:\Documents and Settings\dawns
Volume in drive \\Server01\users is Raid 5
Volume Serial Number is 6840-39D2

Directory of \\Server01\users\dawns

27/04/2007 13:24 <DIR> My Documents
0 File(s) 0 bytes
1 Dir(s) 371,672,825,856 bytes free
Volume in drive \\Server01\users is Raid 5
Volume Serial Number is 6840-39D2

Directory of \\Server01\users\dawns

\\Server01\users\dawns\My Documents LBS-HQ\dawns:(OI)(CI)F
LBS-HQ\SBS Folder
Operators:(OI)(CI)F
BUILTIN\Users:(OI)(CI)(special
access:)

SYNCHRONIZE

FILE_APPEND_DATA

BUILTIN\Administrators:(OI)(CI)F
NT AUTHORITY\SYSTEM:(OI)(CI)F
CREATOR OWNER:(OI)(CI)(IO)F
BUILTIN\Users:(OI)(CI)R
BUILTIN\Users:(CI)(special
access:)

FILE_WRITE_DATA

"Pegasus (MVP)" wrote:

Fine, your feedback is very informative although it does
not yet tell me what's wrong. Now please type this command,
then post c:\test.txt again. Note that I deliberately omitted
the /d switch:

xcopy /s /e /y /c "%UserProfile%\My Documents"
"\\Server01\users\%UserName%\My Documents\" > 1>c:\test.txt 2>&1

As a separate question: Did you make sure that the
"Share" permissions (as opposed to the NTFS permissions)
of \\Server01\users are set to "Full access" for everyone?

"Logie Bear" <LogieB...@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in
message
news:60712D73-BD21-4A7E-9837-1CF912EDCC84@xxxxxxxxxxxxxxxx
Still no joy - same error message . I got the SFN's from DOS
anyway by
navigating to the directory in question.
The contents of the c:\test.txt file are

USERDNSDOMAIN=LBS-HQ.LOCAL
USERDOMAIN=LBS-HQ
USERNAME=dawns
USERPROFILE=C:\Documents and Settings\dawns
Volume in drive \\Server01\users is Raid 5
Volume Serial Number is 6840-39D2

Directory of \\Server01\users\dawns

27/04/2007 13:24 <DIR> My Documents
0 File(s) 0 bytes
1 Dir(s) 371,672,825,856 bytes free
Volume in drive \\Server01\users is Raid 5
Volume Serial Number is 6840-39D2

Directory of \\Server01\users\dawns

\\Server01\users\dawns\My Documents LBS-HQ\dawns:(OI)(CI)F
LBS-HQ\SBS Folder
Operators:(OI)(CI)F

BUILTIN\Users:(OI)(CI)(special
access:)

SYNCHRONIZE

FILE_APPEND_DATA

BUILTIN\Administrators:(OI)(CI)F
NT
AUTHORITY\SYSTEM:(OI)(CI)F
CREATOR
OWNER:(OI)(CI)(IO)F
BUILTIN\Users:(OI)(CI)R
BUILTIN\Users:(CI)(special
access:)

FILE_WRITE_DATA

"Pegasus (MVP)" wrote:

"Logie Bear" <LogieB...@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in
message
news:60F433CE-C216-4BDF-A3E9-F95413DBCCC8@xxxxxxxxxxxxxxxx
I have used xcopy on a number of machines but there is one
which
is
giving
me
grief. The command I use is the same on all machines
(apart
form
the
name)
and is as follows:

xcopy /s /e /d /y c:\docume~1\username\mydocu~1
\\server01\users\username\mydocu~1

Like I said it works a treat on all apart form one. When I
run
it
on
one
machine I get the error message Access Denied Unable to
create
and
then
the
name of the destination directory. The directory exists
and
the
particular
user has full access to it just as I set up all the
others.
Any ideas?

Why would you use 8.3 folder names? Since "My Computer"
shows you LFNs, you can never be sure that your SFNs really
correspond to the LFNs you wish to copy. This command
would be much more robust:

...

read more »

I have not read all the posts here, since there are too many, yet once
I was having similar 'inexplicable' problems and it turned out to be a
NIC issue.

The problem in my case was two cards conflicting, the best way around
this is to test it whilst ALL other machines on the network are
powered off/or disconnected, and if that fails, swap out the NICs in
turn.

Once again, apologies if I am repeating something that was already
said, yet I don't have the time to read through all.

.

Relevant Pages

  • BizTalk 2004: File Receive Location Problem
    ... exhausted network retry events. ... object / current commands counter in PerfMon and that if the value is to ... "FileReceivePollingInterval" for the biztalk service to 1 to prevent ... "Shows the number of requests to the Redirector that are currently queued ...
    (microsoft.public.biztalk.general)
  • Re: xcopy access denied
    ... "Pegasus (MVP)" wrote: ... As a separate question: Did you make sure that the ... "Share" permissions (as opposed to the NTFS permissions) ... Volume in drive \\Server01\users is Raid 5 ...
    (microsoft.public.windowsxp.general)
  • Re: Modelling Complex Sentences
    ... re-inventing the network data model). ... If such as classifying node does not exist, ... Since people complained that dbd's scripts were too long, ... you typically use the CREATE/INSERT commands to ...
    (comp.databases.theory)
  • Re: Server Advice Wanted.
    ... > RAID 0+1 will be more efficient (stripping and mirroring), ... which is why you see it less than RAID 5. ... > could still restore from backups because it takes day to do so, ... a network backup solution. ...
    (borland.public.delphi.non-technical)
  • Re: Segregating networks VLANs or Subnets
    ... network, you can leave NTFS permissions alone. ... the firewall can route just as well. ... > Microsoft Internet Security & Acceleration Server: ...
    (microsoft.public.windows.server.networking)