Re: Can Only Boot with Boot CD in Drive

Paige Miller wrote:
On 10/4/2006 11:28 PM, Justin Case wrote:

I don't think you realize all that you have done. I believe you now have TWO installations of Windows, one on the 80G, and one on the 160G. The original apparently is corrupt. The boot files remained there when you reinstalled to the wrong (the 80G) drive. Therefore the 160G boots.
[Rightclick My Computer. Choose Manage. Under Storage in the left pane, click Disk management. Which drive says "System", which says "Active" ("Boot"), etc. in the right pane? (This is the Disk SnapIn Tool, and may cause you to reinstall everything, if used to make changes without proper Knowledge.)


Currently, the D: drive (the 80gig drive that used to be my C: drive) is listed as Boot, while the C: drive (the 160gig drive that used to be my D: drive) is listed as system.

As of Now, ANY programs installed with the first Windows install are pointing to the wrong drive, because when you installed the 2nd Windows, THAT became the C: drive according to Windows. So ANY/ALL programs not reinstalled are skewed, and any leftover parts are, too.
Best bet: total reinstall of entire system.(if it was me)
To make Photoshop work (possibly), as is: replicate the path to the the library with empty folders on the D: drive, and copy the final library folder at the end of the path.
That is: If program's path says D:\Program Files\Adobe\Photoshop\Library, open D:\Program Files and just make a New>folder named Adobe, make a folder inside it named Photoshop, then copy and paste the library folder inside of that. May work; don't know what all else you've reinstalled, or haven't.
I'd start over.


To start over, do I need to erase these system files from one of my drives? Specifically, do I need to get rid of (or move to the other drive) NTLDR, NTDETECT.COM, and BOOT.INI?

When I insert the Recovery disk to re-install windows, it always refers to my drives backwards ... in other words, the original C: drive (80gig) was always referred to by this program as my D: drive. I'm sure this is part of the confusion that I am having.

You are definitely correct about Photoshop Album, but I want my data files on a different drive from my Windows installation, just in case I ever have to do a re-install.

Place the drive on which you want to install Windows at the Master position on the Primary IDE controller. Keep the other drive(s) OUT of the machine until you have Windows installed properly and up and running, these other drives can be brought online after you install Windows. That will avoid mix ups and errors like the one you experienced. Just be sure to place the Windows drive at the position as I said earlier. Format the drive and reinstall Windows properly. Once you are satisfied that Windows is properly installed and running properly shut down the computer and install your other drive(s).

After installing the other drive and BEFORE you reboot Windows start the computer with a BootItNG diskette. http://www.terabyteunlimited.com/bootitng.html This is a fully functional 30 day trial version. Following the instruction from the site above create a boot diskette. DO NOT INSTALL BootItNG! It will work from a diskette boot, like a Windows 9x DOS boot diskette, just hit Escape or click cancel and it will tell you that it's entering "Maintenance Mode" (or something like that). Once there remove the "Active" flag from any partitions on the second hard drive. BE CAREFUL! Don't mix up your drives and don't remove the active flag on the Windows System Partition! Once done remove the BootItNG diskette and reboot the computer to your Windows Installation.

If the computer doesn't boot properly, you stuck the drives in the wrong place or the Master/Slave jumpers are wrong. Just make sure that the Windows installation is on partition 1 on HDD0, and that this is the drive set to boot in the BIOS.

John

.

Relevant Pages

  • Re: Installing XP Pro on Hard Drive
    ... Windows 2000 Pro, but I want to install a retail version of Windows ... and set to boot from a Windows 98SE startup floppy. ... By the way, the BIOS recognizes both optical drives, and even in Device Manager, the optical drives are recognized, and 'working properly'. ... I decided to install Windows XP Pro on to a larger, Western Digital 160GB hard drive that I had on the shelf from a few years ago, and see if the optical drives would work under XP. ...
    (microsoft.public.windowsxp.help_and_support)
  • Re: I Forced a Shut Down During a Memory Dump...
    ... Windows, then shows a black screen with a progress bar along the ... boot sector. ... to re install windows, repair windows ... It tries to detect the drives ...
    (microsoft.public.windowsxp.general)
  • Re: I Forced a Shut Down During a Memory Dump...
    ... load Windows, then shows a black screen with a progress bar along ... boot sector. ... to re install windows, repair windows ... It tries to detect the drives ...
    (microsoft.public.windowsxp.general)
  • Re: Start Menu, Icons Not Appearing
    ... Also, make sure your system has no malware, download, install and run Ad ... Assuming your system is set to boot from the CD-ROM drive, ... To Setup Windows XP now, ... To Repair a Windows XP Installation using Recovery Console press R. ...
    (microsoft.public.windowsxp.accessibility)
  • Re: Cannot Boot Into any Option for Safe Mode
    ... I used PQ Magic 8 to create 5 other logical drives for programs, ... cannot install anywhere else. ... so I ended up with windows installed on NTFS and the rest of the drive being ... - but only if trying to boot into anything after pressing F8 on startup. ...
    (microsoft.public.windowsxp.newusers)