Re: connection unavailable

In E5A55B7E-D834-448C-857B-B3CADB3725D7@xxxxxxxxxxxxx Jeri
wrote:
> "Nepatsfan" wrote:
>
>> In 90859804-16BA-4710-902A-E70E1150D2EF@xxxxxxxxxxxxx Jeri
>> wrote:
>>> I have a netgear MA111 wireless modem on my main PC and the
>>> adapter on my PC
>>> in the other room. Problem is that whenever my PC with the
>>> adapter is
>>> shutdown for any reason when I reboot I loose my connection
>>> and it takes
>>> forever for me to get it back. Device manager says it is
>>> working properly.
>>> When I click on the PC icon (which is red) I go to
>>> connection
>>> tab it's set to
>>> Ad hoc, first available access point but I don't get a
>>> signal. (says signal
>>> is unavailable) If I play around with it sometimes it will
>>> just start working
>>> all of a sudden. There is no reason why sometimes it work
>>> and
>>> sometimes it
>>> doesn't. I know it can get a signal because once it starts
>>> working it will
>>> stay running until that PC goes down. Could there be a
>>> problem with firewalls
>>> on my main PC which blocks the other one from accessing the
>>> signal? Sorry so
>>> long, any input would be greatly appreciated. Thanks
>>
>> Jeri,
>>
>> How exactly is your network configured? Do you have a
>> wireless
>> router or access point?
>>
>> A Netgear MA111 is a wireless USB adapter. It's normally
>> used
>> to connect a PC to a wireless router which is then connected
>> by
>> ethernet cable to a modem which is connected to the
>> internet.
>>
>> Ad hoc mode is used to setup a computer to computer network.
>> Are you running Internet Connection Sharing on your main PC?
>> If
>> not, any wireless adapters should be set for Infrastructure
>> mode.
>>
>> Bottom line, if you don't have a wireless router, get one.
>>
>> Good luck
>>
>> Nepatsfan
>>
>>
>> Thanks for responding, your right it is set to
>> infrastructure. I have a wireless
>> router setup on my main PC which is connected to a comcast
>> cable modem. For some
>> reason my netgear adapter will not pickup a signal it says
>> ``wireless connection
>> unavailable''. If i set my connection to Ad-hoc I will be
>> able to send a signal but I
>> cannot receive a signal. Like I said before sometimes after
>> switching back and forth
>> it will eventually connect to the infruastructure setting
>> and then I'm good to go. But
>> as of now after trying for hours (my electricity shut off so
>> my PC went down) I cannot
>> get it to work. I have looked into setting up a home network
>> but I don't think it
>> really has anything to do with that since it has worked
>> before without a network.
>> Someone told me they have to power down their router
>> everytime to get their wireless
>> adapter to pick up a signal but I have tried that and it
>> doesn't work for me. Do you
>> think there could be a firewall blocking the signal? Thanks
>> again for
> your help. I am very new to all this as I'm sure you can
> tell.

First off, go to Netgear's web site and download the latest
driver for your adapter.

MA111 Family Support Page with Links
http://kbserver.netgear.com/products/MA111.asp

Check the label on your adapter and make sure you download the
driver for the correct version.

Once you've installed the latest driver, logon to your router's
web interface from your main computer. Consult the
documentation that came with your router for how this is done.
Once you've logged on, look for a section that will allow you
to change the wireless settings. You want to change the channel
that the router uses for wireless connections from the default
channel to channel 1. If you're not able to do this, post back
with details for your router (make and model #).

Make sure you're using Infrastructure Mode.

If you're still not able to connect, you might want to contact
Netgear's support at 1-888- Netgear. You can also contact them
via email. They have their own support forums which you may
find helpful.

How to Contact Netgear
http://kbserver.netgear.com/kb_web_files/n100005.asp

FYI #1, a firewall should not prevent you from establishing
communications between your wireless adapter and the router. If
this was a firewall problem, you'd be able to connect to the
router (the network connection icon would be green) but you'd
have a problem connecting to the internet.

FYI #2, after a power failure, it's usually a good idea to
leave the computers off and disconnect the power cables from
the modem and router. Once the power comes back on you plug the
cable back into the modem first. Once the modem's up and
running, reconnect power to the router. Finally, restart the
computers.

Good luck

Nepatsfan



.

Relevant Pages

  • Re: TV service query ? ? ?
    ... a wireless router. ... a router with extended coverage. ... cable and a wireless connection that you can not see. ... is to have users downloading r/t video, large video files, or other ...
    (alt.home.repair)
  • Re: Xbox 360 and Media Center Connectivity Problems
    ... between the media center pc and the xbox 360.... ... will have to try and research a wireless router/access point that will not ... deter the extender and media center from holding a connection... ... via the router, with the MCE ...
    (microsoft.public.windows.mediacenter)
  • Re: My Network Places
    ... What you want is to set your router's IP, and thus your router's DHCP server, to use a subnet that is different than the one being used by your provider's router. ... I'm not sure why you are using a bridge and separate wireless router rather than merely wirelessly connecting direct to your "provider's" router, but there is a definite plus: because you have your own wireless router, you can effectively isolate yourself from the other users on your provider's router. ... As soon as you click the "Save Settings" button, you will lose your connection, because your computer will now be on a different subnet. ... It does not provide any security and it may cause problems, ...
    (microsoft.public.windowsxp.network_web)
  • Re: wireless download speed
    ... Also, if this was done using a wireless connection, you can get a very ... In the case of a cable modem, ... and router rules can slow the router down. ...
    (alt.internet.wireless)
  • RE: Win XP no longer able to access LAN with win 98SE machines
    ... for your wireless adapter. ... wired adapter installed on one of my XP machines and the upgrade to XP SP2 ... the wired router is connected to port one of a wireless router, ...
    (microsoft.public.windowsxp.network_web)
Loading