Re: Can TAP.exe run in Windows XP embedded?
- From: "Sean Liming \(MVP\)" <sean_liming@xxxxxxxxxxxx>
- Date: Wed, 16 Jan 2008 08:40:47 -0800
How much RAM do you have in the system?
--
Regards,
Sean Liming
www.sjjmicro.com / www.seanliming.com
Book Author - XP Embedded Advanced, XP Embedded Supplemental Toolkit
"tunde tosh" <tundetosh@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message news:EF0E0E6B-1863-4374-8000-9F47814D650A@xxxxxxxxxxxxxxxx
The XP Pro was installed on a 20 GB hard drive. Then it wasn't complaining of
low virtual memory. It's when I install the small XPe image on the 1GB
compact flash that I get that complaint even though it goes on to install it
but has problems installing some DLLs. I will try booting with WinPE as Ethan
has suggested.
"Sean Liming (MVP)" wrote:
Installing XP Pro is going to require more the 1GB of storage space. If
there is a smaller XPe image available, run TAP.EXE on it. Just be aware
that you might not capture all the drivers more specifically the codecs for
meultimedia.
TA.EXE is possisble, but it doesn't capture everything required to boot an
image -
http://www.seanliming.com/Docs/XPE%20Stop%200x0000007B%20Error%20V1.3.pdf
--
Regards,
Sean Liming
www.sjjmicro.com / www.seanliming.com
Book Author - XP Embedded Advanced, XP Embedded Supplemental Toolkit
"tunde tosh" <tundetosh@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:E1784A7C-BA93-4704-8550-4505A2B4C2BF@xxxxxxxxxxxxxxxx
>I have an old motherboard (SBC 84500) that I have upgraded it's BIOS so >I
>can
> boot from a CF. I had installed Win XP Pro on it using a hard drive so > as
> to
> get the drivers using TAP. It ran on it though slow because it wasn't
> really
> meant for it. However, a few drivers were missing even when I had
> installed
> the board drivers.
> The manufacturers say Win XP can run on it though it's not advisable
> because
> the processor is to solve. However, they also say Win eXP can run on > it. I
> have been given a simple XP image download to try on it. At present, I > am
> trying to install it though it keeps complaining of low virtual memory
> during
> FBA. I guess it's because the CF is only 1GB.
> The possibility of the cause of the problem I had reported is likely > due
> to
> missing drivers because at a stage during this long experiment it had
> complained about the hal.dll. I tried playing a fast one by > substituting
> the
> hal.dll file the eXP image had with the one that worked with XP Pro but > it
> wasn't successful.
>
> "tunde tosh" wrote:
>
>> I have been trying to build an image for a machine with an old
>> motherboard.
>> This has proved unsuccessful. However, I got a basic pre-built image >> from
>> the
>> motherboard's manufacturer which runs. Can I run TAP in that image so >> as
>> to
>> import it into XPe target designer?
>>
.
- References:
- Re: Can TAP.exe run in Windows XP embedded?
- From: Sean Liming \(MVP\)
- Re: Can TAP.exe run in Windows XP embedded?
- From: tunde tosh
- Re: Can TAP.exe run in Windows XP embedded?
- Prev by Date: Re: Can TAP.exe run in Windows XP embedded?
- Next by Date: Re: Hibernation protecting other disk??
- Previous by thread: Re: Can TAP.exe run in Windows XP embedded?
- Next by thread: Re: Can TAP.exe run in Windows XP embedded?
- Index(es):
Relevant Pages
|
