Re: Bootable CD problem
- From: "Sean Liming \(eMVP\)" <sean_liming@xxxxxxxxxxxx>
- Date: Fri, 23 Mar 2007 17:15:08 -0700
My next question is can you boot XPe from a USB flash disk? The reason is
that if you can't then USB boot CD-ROM is not go to matter since your
system's BIOS doesn't support it.
Regards,
Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
"Sean Liming (eMVP)" <sean_liming@xxxxxxxxxxxx> wrote in message
news:%23Z1QIjObHHA.4772@xxxxxxxxxxxxxxxxxxxxxxx
They finally looked into it. Are you using a uDOC or just an off the shelf
USB flash drive?
Regards,
Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
"Dan" <Dan@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:24B21C42-42C0-40AB-A9A3-8AA5845DADB1@xxxxxxxxxxxxxxxx
PF2007 help file.
This link shows a success of XPe CD for a USB
http://blogs.msdn.com/embedded/archive/2006/10/23/advanced-scenario-usb-el-torito-booting-from-usb-cd-rom.aspx
how about the answer for question 1?
Thanks
"Sean Liming (eMVP)" wrote:
What documentation are you refering too?
There have been some attempts to create an XPe Bootable CD ROM for a USB
CD-ROM drive. All the documentation to date has been for XPe IDE CD-ROM
boot. XPE USB CD-ROM boot is a new endevor because FP2007 has USB Boot
2.0
support. The new USB Boot 2.0 supports booting from USB flash disks. I
am
not sure if the XPe team tested the support for USB CD-ROMs.
Regards,
Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
"Dan" <Dan@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:4F986F8C-6F34-4833-860B-F44D991E7203@xxxxxxxxxxxxxxxx
I have two problems
1/ format 650MB primary partition with FAT32, set active using dispart
in
WinPE2. After I fill this partition with pre-FBA image, it does not
boot.
I
have to use bootprep /dC to config. It then boots and I want to know
what
went wrong here since your doc said " FAT32 do not need bootprep."
2/ I put a pre-FBA CD on the USB CD (This is the only CD driver in my
tablet). I created 2 primary partitions 650MB each of the 80GB HD, one
C:
for
CD and one D: for a normal hard drive XPe image. I set boot.ini to
boot to
D:
to prepare pre-FBA CD from C:. Later, I boot into C: to prepare the
final
image. In my case, I set Boot CD first.
I boot the system into C: to run FBA with a pre-FBA 700MB CD in the
USB CD
Driver.
For the first time the image runs FBA, reboot and later it comes back
says
"
Missing operating system"
What did I do wrong? set HD boot first and USB-CD later?
My prepare image has no problem with El Torito support, USB 2 boot
ets...I
also disable start option in EWF...
Your document messes up my mind.
Hope you, experts, help me to build a successful XPe bootable CD.
I am using Feature Pack 2007, my sytem is a tablet with one HD
Thanks,
.
- References:
- Re: Bootable CD problem
- From: Sean Liming \(eMVP\)
- Re: Bootable CD problem
- From: Dan
- Re: Bootable CD problem
- From: Sean Liming \(eMVP\)
- Re: Bootable CD problem
- Prev by Date: Re: Missing Component Building XPPro Emulation - Kenel-FP1
- Next by Date: Re: Is there such a beast as XP x64 embedded
- Previous by thread: Re: Bootable CD problem
- Next by thread: Re: Bootable CD problem
- Index(es):
Relevant Pages
|
