Re: EWF RAM MODE: ERROR 1
- From: "KM" <konstmor@xxxxxxxxxxxxxxxxx>
- Date: Thu, 11 Jan 2007 08:43:05 -0800
sand,
XP disk manager can't create partition smaller than ~8Mb.
EWF RAM Reg mode will allow you to get rid of the EWF Config partition but
keep all the ewf config info in the registry.
If you are working with XPe FP2007 the EWF RAM Reg mode is very easy to set
up there.
Regards,
KM
thanks for your help :-) your post has been very userful. How you know
that
the free unallocated space must be 8MB?? there is any criteria about
this?.
And why you recommend me use RAM REG? only for pass haveing to have a
second
partition??
thanks
sand
"Sean Liming (eMVP)" wrote:
For hard drives above 4GB capacity, you need 8MB of free unallocated
space
for the EWF volume to be created. 7.4MB is too small. You could setup RAM
REG instead and by pass haveing to have a second partition for EWF.
Regards,
Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded
SupplementalToolkit
"sand" <sand@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:B9B7C233-116B-4AAD-8F1A-44E07EEF107F@xxxxxxxxxxxxxxxx
Hi! I'm developping my image and I want to configure EWF in a hard disk
ATAPI/IDE. My hard disk only contains prymary partition, so I create
the
EWF
volume in the unallocated disk area (7,4 MB). When I typing ewfmgr d: I
obtain an error 1. But in the FBALOG it seems all go good:
9:51:55 - ConfigureEwf() Start.
9:51:55 - Getting EWF config parameters from registry.
9:51:55 - Non El Torito disk configuration.
9:51:55 - EWF Partition Size = 0 (KBytes), Levels = 1, Volumes = 1.
9:51:55 - Protected Volume Config #0 :
9:51:55 - Disk= 1,Part= 1,DiskType= IDE,Type= RAM.
9:51:55 - Enable= Enabled, Optimize= 0, LazyWrite= N.
9:51:55 - Found 2 Hard Disks.
9:51:55 - Disk #0 layout info:
9:51:55 - PRIMARY partition,start=0x0000000000007e00,
len=0x0000000950280000, type= 7
9:51:55 - FREE partition,start=0x0000000950287e00,
len=0x00000000007d8200,
type= 0
9:51:55 - Allocating EWF in PRIMARY partition,
start=0x0000000950287e00,
len=0x000000000000fc00.
9:51:56 - Created EWF partition on Disk = 0, partition = 2,size =
0x000000000000fc00 .
9:51:56 - ewfOpen.
9:51:56 - EWF Volume Config on Disk#0, Partition#2:
9:51:56 - Segments = 0, Max Volumes = 1, Max Levels = 1
9:51:56 - ewfAdd.
9:51:56 - Protected Volume Config on Disk1\Partition1 :
9:51:56 - Type = RAM, State= ENABLED.
9:51:56 - ewfClose
9:51:56 - Saving EWF configuration to registry:
9:51:56 - Protected Volume ArcName =
multi(0)disk(0)rdisk(1)partition(1).
9:51:56 - ConfigureEwf() End, status = 0x0.
9:51:56 - [CallEntryPointThread] D:\WINDOWS\system32\ewfdll.dll,
ConfigureEwf
9:51:57 - [FBASetProgressText] Resetting Setup Flag...
9:52:01 - [FBADoReboot] Sleeping...
9:52:11 - [FBADoReboot] Rebooting system...
Very thanks for your help
sand
.
- References:
- EWF RAM MODE: ERROR 1
- From: sand
- Re: EWF RAM MODE: ERROR 1
- From: Sean Liming \(eMVP\)
- Re: EWF RAM MODE: ERROR 1
- From: sand
- EWF RAM MODE: ERROR 1
- Prev by Date: Re: VGA disabled black, video is routed to LVDS
- Next by Date: Re: the list of all component changes in Feature Pack 2007
- Previous by thread: Re: EWF RAM MODE: ERROR 1
- Next by thread: Re: EWF RAM MODE: ERROR 1
- Index(es):
Relevant Pages
|
