Re: Running a driver application

Try konstmor At hotmail Dot com.

--
=========
Regards,
KM

Hi KM,
All the files seem to be located in their corresponding folders.
Sure, I can share the component with you. Would you like to share your
mail-id to share the component?
rgds

"KM" wrote:

sirish,

Is it possible for you to share the component with us here? I can check the component integrity and let you know if it was
properly
created.

Also, are you sure your component includes all the files for the drivers? Did you create a repository and associated it with the
component? Does you pre-FBA image include all the files for the driver located in the corresponding folders (\windows\inf,
\windows\system32, \windows\system32\drivers, etc.).

--
=========
Regards,
KM

I Have got another observation: I do see the analysis toll component during
build process but it doesn't show the component name when showing the
estimated component sizes!
Any guesses?


"KM" wrote:

Sirish,

The exe you are referring to may be checking the state of the driver you mentioned and if installed (load and run) properly it
may
execute one code path but if not - another.

Without knowing what that executable does it is going to be hard to guess what's missing from your image.

I left more comments in another thread you created.

--
=========
Regards,
KM


Hi KM,
Sorry for the vague description earlier! You are right the new thread posted
today refers to this question only.

Following are the details.
It was about Kvaser PCIcan driver on my XPe image. I componentized the
kvaser s/w provided by importing its INF file.
The installation should show: CAN h/w (Kvaser) - 1)Kvaser PCIcan 2) Kvaser
Virtual CAN driver, in the device manager.
The two (I guess) go in combination and consists of the h/w driver and GUI
based interactive 'CAN bus monitor/analyzer'.

The problem is even on including the corresponding components of 1&2 while
building my image, I see only CAN h/w (Kvaser) - 1)Kvaser PCIcan, in the
device manager.
When I try to open the corresponding exe file to open the analyser, it gives
error which says 'Configuration program could not be started. Try to
reinstall the driver'!

I used 'depends' tool to check if any file is missing but no. I then used
'filemon' and 'depends-profile' tools on which I understand though all the
files are present, the execution procedure is different. Example: After
executing (file calls and results being) exactly the same way on both
platforms, a call to 'COMCTL32.DLL' is made on XPe where as a call to
'SHLWAPI.DLL' is being made on XP-prof.

The last few similer file calls before they differ are for: ... USER32.DLL,
GDI32.DLL, WINSPOOL.DRV. Later on their excution is entirely different.

You suggested, the path of installation may vary. Does it apply in my case
(I mean even when I import from INF file)? Any suggestions what components
could possibly be missing in my XPe image?

Regards
Sirish

"KM" wrote:

sirish,

Would you mind to explain what you meant by "driver application"?
Is it an installer for a driver or something else?

If you're talking about a driver installer...
There could be many reasons why it runs differently on XPe vs XPP. E.g.:
- the installer checks for the OS version to change the install code path.
- the installer checks for a presence of specific components (Dll, etc.) and that may affect the code path as well.
- some error handling of the installer app may affect its code routes. (keep in mind that it may have happened that
your
XPe
image doesn't have all the components required by the installer)
- etc.

Too look more carefully at he problem you'd probably need to send out a bit more info (e.g., be specific about what you're
trying
to
install, FileMon logs, etc.)


--
=========
Regards,
KM

Hi,
The driver application run on XPe OS seems to be running differently. I
mean, different files are being accessed when the same executable is run from
XP prof and XPe (learnt using FileMon tool). The different behaviour starts
after half the similer process.

Can some one please describe what could be the reason?

Regards











.

Relevant Pages

  • Re: Running a driver application
    ... execute one code path but if not - another. ... It was about Kvaser PCIcan driver on my XPe image. ... - the installer checks for the OS version to change the install code path. ...
    (microsoft.public.windowsxp.embedded)
  • Re: Running a driver application
    ... execute one code path but if not - another. ... It was about Kvaser PCIcan driver on my XPe image. ... - the installer checks for the OS version to change the install code path. ...
    (microsoft.public.windowsxp.embedded)
  • Re: Running a driver application
    ... It was about Kvaser PCIcan driver on my XPe image. ... - the installer checks for the OS version to change the install code path. ...
    (microsoft.public.windowsxp.embedded)
  • Re: Running a driver application
    ... The exe you are referring to may be checking the state of the driver you mentioned and if installed properly it ... execute one code path but if not - another. ... It was about Kvaser PCIcan driver on my XPe image. ... - the installer checks for the OS version to change the install code path. ...
    (microsoft.public.windowsxp.embedded)
  • Re: Running a driver application
    ... The exe you are referring to may be checking the state of the driver you mentioned and if installed properly it ... execute one code path but if not - another. ... It was about Kvaser PCIcan driver on my XPe image. ... - the installer checks for the OS version to change the install code path. ...
    (microsoft.public.windowsxp.embedded)