Re: How do I deploy my Image to the Target Device?
- From: "Brad Combs" <brad@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx>
- Date: Fri, 9 Dec 2005 16:58:31 -0500
Hello,
Sounds like you have a good start.
As for the command prompt, when Target Designer asked you to choose a shell
did you by chance choose the Command Shell? If your looking for the standard
explorer shell choose "Explorer Shell" instead.
HTH,
Brad
"W Schmoegner" <WSchmoegner@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
news:8EAEB768-BE6D-499F-8636-1C8D8ABEE195@xxxxxxxxxxxxxxxx
> My target device is a Kontron EPIC CE using a Celron CPU running at 733MHz
> with 512MB RAM.
> A hard disk drive connected to the EIDE Primary Master.
> Has a Compact Flash Type 1 as EIDE Secondary Master,6 USB Ports.
> http://www.kontron.com/products/pdproductdetail.cfm?keyProduct=40772&kps=2941&kpc=75
>
> What I did was to use Partition Magic to resize my HD, already has a XP
> Pro
> install
> Then I used Disk Manager to create and format a new Primary Partition and
> shared it.
>
> Next I copied all the files from the XPe image folder on my development
> platform to the Partition created above.
> I then edited the boot.ini file to multi-boot the target devcie.
>
> To make a long story short, I boot to the XPe image, FBA runs, I believe
> successfully.
>
> My problem is, that when I logon to XPe, it dumps me to the command shell
> at: c:\windows\system32.
>
> Why is this?
> Do I need to do something else?
> I searched through the MSDN and it wasn't much help.
>
>
> "Brad Combs" wrote:
>
>> Hello,
>>
>> Can you give us some more information about your target device?
>> Suggestions
>> will vary slightly based on what type of access you have to the system.
>> For
>> example if you are trying to build an image for a system with a hard
>> drive
>> and you can take that hard drive out of the device that will make life
>> easier. You can simply put the hard drive in your development system,
>> create
>> a partition, format, mark it as active, and copy the files from Target
>> Desingers build folder to it. Then shut down the development PC and move
>> the
>> disk back to your target. Boot up the target to run FBA.
>>
>> Another option is to boot to Windows PE, map a drive to a network share
>> that
>> has the Target Designer files in it and use xcopy to copy the files to
>> the
>> local disk in the device. This assumes you have a CD-Rom or a USB CD-Rom
>> attached to the device. Disk 1 of the XP Embedded tools is a bootable CD
>> containing WinPE. Try that out just for fun. :-)
>>
>> If you continue to work with XPe you'll eventually gather an aresenal of
>> USB
>> adapters to get different types of disks attached to your development
>> system
>> so that you don't have to open the development system up all the time.
>> Take
>> a look at these:
>>
>> http://froogle.google.com/froogle_cluster?q=USB+IDE+Adapter&pid=4825516905212234853&oid=16456801425805449729&btnG=Search+Froogle&lmode=&addr=&scoring=p&hl=en
>>
>> This is the item that I use the most for physically moving the drive
>> around
>> (it has both 40 pin 3.5" drive connection and a 44 pin 2.5" drive
>> adapter).
>> I use WinPE in situations where I can't get at the drive or don't need to
>> because there is a CD-Rom present.
>>
>> Again, let us know more about your device and we can give you quite a few
>> ideas.
>>
>> P.S. Coming from the Platform Builder world be aware that the "debug"
>> image
>> in XPe is useless so always build a release version.
>>
>> HTH,
>> Brad
>>
>> "W Schmoegner" <WSchmoegner@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message
>> news:EE9E8DAD-73AF-4BE0-A0EB-4569B25A9A43@xxxxxxxxxxxxxxxx
>> > Newbie question here.
>> >
>> > I have system running XP Pro that I have XPe Embedded Studio installed
>> > on.
>> > The image I am developing is for another system.
>> >
>> > How do I get that image running on my target system?
>> > I have read the Create bootable CD, Install to a Hard Disk, Compact
>> > Flash
>> > device, etc.
>> >
>> > What is the easiest way to do this?
>> > WinCE has PB that allows a download of a boot image via a network
>> > connection, and you are able to debugg the image that way.
>> >
>> > Can something like this be done with XPe Embedded Studio?
>> > I just need some info to point me in the right direction.
>>
>>
>>
.
- References:
- Re: How do I deploy my Image to the Target Device?
- From: Brad Combs
- Re: How do I deploy my Image to the Target Device?
- From: W Schmoegner
- Re: How do I deploy my Image to the Target Device?
- Prev by Date: Re: sdimgr xxx.sdi /writedisk:0 /yes fails
- Next by Date: Re: FBA Generic Command Problem
- Previous by thread: Re: How do I deploy my Image to the Target Device?
- Next by thread: Help with Remote assistance
- Index(es):
Relevant Pages
|
|
