Re: What "EWF RAM REG" XPE computer can do???

I'm not too familiar with the memory requirements of various components, and
without knowing specifically which components you're using, I couldn't tell
you if your memory size is sufficient to run them. However, on a general
basis, you can achieve better memory efficiency by doing the following:

(1) Remove any components from your configuration that you don't absolutely
need for your runtime. Some Windows components do more writes to the system
drive than others (eg. to store configuration information, write to the
Event Log, etc.) - the less of these components you have, the better.

(2) Optimize your application and any Windows components to minimize the
number of writes they do to the system drive. You should save data only
when necessary - spurious writes will use up your RAM overlay faster.

(3) Format your runtime partition in FAT16 or FAT32, as opposed to NTFS
(unless you need the extra security features or compression capabilities of
NTFS). NTFS tends to update itself frequently and performs more write
operations in general than FAT, so it will use up the RAM overlay faster.

My recommendation would be to try these things above, and then evaluate if
you are still using a lot of memory. You might try including the Task
Manager component and using it to determine how much Available Physical
Memory you have. (The total amount of Virtual Memory will appear at or
slightly below your total physical memory if you've turned off the swap
file.) The higher this number is, the better, but keep in mind that it may
not give you a completely accurate picture of your available RAM because the
EWF overlay is taking up some of that space. You can use this value in
conjunction with "EwfMgr C:" to get an idea for how much actual memory you
have available.

Once you've determined that, you can evaluate whether you'll need to install
more RAM in your target system.

BTW, I re-read your original message and noticed that you mentioned using
the Internet, presumably with Internet Explorer. Here's some additional
info specific to that scenario:

When using Internet Explorer, keep in mind that by default, it caches local
copies of the pages and images you've visited. It saves these local copies
to the system drive, which means the data will be intercepted by EWF and
cause the RAM overlay to grow. You can disable IE's caching behavior, but
this can significantly increase page load times and bandwidth usage if you
frequently access pages not stored on your local hard drive. When building
your runtime, if you do not need to use IE, I would recommend removing it
from your configuration.

Hope this helps. =)

--
Matt Kellner (mattkell@xxxxxxxxxxxxxxxxxxxx)
STE, Windows Embedded Group

This posting is provided "AS IS" with no warranties, and confers no rights.
===============================

"XPEnew" <new@xxxxxxx> wrote in message
news:OA07%23QevFHA.1252@xxxxxxxxxxxxxxxxxxxxxxx
> Matt, thank you very much!
>
> Our PC has 128 or 256MB, are they too small???
>
> "Matt Kellner (MS)" <mattkell@xxxxxxxxxxxxx> wrote in message
> news:%230MYjxwuFHA.3596@xxxxxxxxxxxxxxxxxxxxxxx
>> Hi XPEnew.
>>
>> On 1: How much memory does your target system have? The lower the amount
> of
>> RAM, the more likely you are to see the "Delayed Write Failed" message.
>> This is usually a result of the system running out of memory. (Keep in
> mind
>> that RAM and RAM Reg overlays store all write operations in memory, so
>> the
>> memory overlay grows as more data is written.)
>>
>> Also, ensure that your configuration is not setup to use a swap file. If
>> you have a swap file in your runtime, this will eat up your RAM overlay
> very
>> quickly.
>>
>> On 2: This is by design. The EWF RAM and RAM Reg overlays intercept all
>> write operations intended for the hard drive that you're protecting -
> hence
>> the name "Enhanced Write Filter". Because these writes are now stored in
>> RAM, all writes (including files saved to the protected partition) are
> lost
>> when the computer reboots or shuts down.
>>
>> If you want to be able to save files to the CF device (such as from your
>> application), I would recommend partitioning your CF device into two or
> more
>> partitions. You would install your OS onto the first partition and setup
>> EWF to protect that partition. Then you would designate the other
>> partition(s) for storing persistent data, and you'd configure your
>> application to save to that unprotected partition. This allows you to
>> persist the data you want while still experiencing the benefit of having
> EWF
>> protect your operating system and your CF device.
>>
>> I wrote an article on a related subject a couple of months ago. Check it
>> out here: http://blogs.msdn.com/embedded/archive/2005/07/08/437033.aspx .
>>
>> --
>> Matt Kellner (mattkell@xxxxxxxxxxxxxxxxxxxx)
>> STE, Windows Embedded Group
>>
>> This posting is provided "AS IS" with no warranties, and confers no
> rights.
>> ===============================
>>
>> "XPEnew" <new@xxxxxxx> wrote in message
>> news:%23BufmhuuFHA.3260@xxxxxxxxxxxxxxxxxxxxxxx
>> > Hello,
>> >
>> > I'm totally new to XPE "EWF RAM REG" image, but we need to build a
> image
>> > for 1G or 2G CF, so I followed the instruction to build "EWF RAM REG",
>> > after FBA, I can run this XPE( I use a regular HD for making image and
>> > testing now, not CF), but after for a while,
>> >
>> > 1 "Delayed Write failed" keep popping up if I run Internet Explorer,
>> > I
>> > have to restart the computer, I then followed the trouble shooting
>> > suggestions, like disable auto defragmentation... but still same, I
> still
>> > see this message pop up when I try to install program or go to
> Internet...
>> >
>> > 2. I save some files to hard drive, but after I restart computer, all
>> > lost!
>> >
>> >
>> > We actually want to install some retail POS software in to this XPE
>> > with
>> > 1G
>> > CF, so looks like we can't use CF at all for this??? What the usage
>> > for
>> > making "EWF RAM REG" computer??
>> >
>> >
>> >
>> >
>> >
>> >
>> >
>> >
>> >
>> >
>>
>>
>
>


.

Relevant Pages

  • Re: XP Pro - Swap File Size for Modern Systems
    ... If you want full memory dumps for analyzing crashes, ... minimum size to at least be equal to the installed ram. ... the partition as well. ... > What is the optimal size for the swap file for Windows XP Pro. ...
    (microsoft.public.windowsxp.general)
  • Re: What "EWF RAM REG" XPE computer can do???
    ... > RAM, the more likely you are to see the "Delayed Write Failed" message. ... > This is usually a result of the system running out of memory. ... You would install your OS onto the first partition and setup ... > protect your operating system and your CF device. ...
    (microsoft.public.windowsxp.embedded)
  • Re: Steve Jobs demos Macintosh in 1984
    ... Woody wrote: ... Stop annoying the fucking hell out of me, ... For sure not much computer memory had been made in 1948 - but it could ... For sure you got a bit more RAM to use in the Speccy - ...
    (uk.comp.sys.mac)
  • Re: Windows uses 4 GB? Really?
    ... I bought 4 GB of RAM because I thought it would speed up my system a bit. ... Some info that is posted here as reference seems to suggest that it is a Windows issue, but others seem to suggest that it is also a hardware issue. ... "I have install total 4GB memory on my motherboard. ... On a SLI system, since PCI-Ex graphic cards will occupy around 256MB, another 256MB will be occupied after you install a 2nd PCI-Ex graphic card. ...
    (microsoft.public.windowsxp.general)
  • Re: Computer wont boot up after installing new RAM
    ... I even took a look at an old Gigabyte motherboard ... DDR2 memory stick, the notch does not line up. ... "To install the memory module, ... into the motherboard RAM slots. ...
    (microsoft.public.windowsxp.hardware)
Loading