Re: Error after executing fbreseal.exe; error code: 0x80090006

From: Slobodan Brcin \(eMVP\) (sbrcin_at_ptt.yu)
Date: 12/29/04

  • Next message: david Gu: "Re: Error after executing fbreseal.exe; error code: 0x80090006" 
    Date: Wed, 29 Dec 2004 09:27:09 +0100

    Hi David,

    > I set a system drive letter 'X:' when I format the HDD, expected the driver
    > letter might be changed to 'C:' when it boots up by HDD, and it really does.
    > (Because, I use WinPE CD to copy my XPE image and WinPE CD occupied 'C:')
    > Does this procedure have related my problem? Can it be a clue for you?

    No this can't be a problem.

    Read following it might give you idea how volume letters are assigned and configured:
    http://msdn.microsoft.com/embedded/community/community/tips/xp/rtpartin/default.aspx

    Regards,
    Slobodan

    "david Gu" <leadus@gmail.com> wrote in message news:AB7FD645-ED9F-49B0-951D-50ECF4586F28@microsoft.com...
    > Thanks for your guide.
    >
    > Some of your instructions are already tried.
    > 1. Q810144 - already applied
    > 2. -keepall switch is also used.
    > and I'll get the registry info. and log file that you required, ASAP.
    >
    > My XPE Image is based on SP1 and all of hotfixs are appied.
    >
    > AND
    > I set a system drive letter 'X:' when I format the HDD, expected the driver
    > letter might be changed to 'C:' when it boots up by HDD, and it really does.
    > (Because, I use WinPE CD to copy my XPE image and WinPE CD occupied 'C:')
    > Does this procedure have related my problem? Can it be a clue for you?
    >
    > David Gu
    >
    > "KM" wrote:
    >
    > > David,
    > >
    > > I don't have a clue but let's debug the problem a little bit.
    > >
    > > Some steps you can do:
    > > - make sure you have this QFE installed:
    > > http://www.microsoft.com/downloads/details.aspx?familyid=6cbe66cb-28d0-49e7-a059-400a7d6059e2&displaylang=en (some more info
    here
    > > http://support.microsoft.com/default.aspx?kbid=810144)
    > >
    > > - use -keepall switch when you run fbreseal.exe. Make sure fbreseal got self-deleted.
    > >
    > > - save (export) [HKLM\SYSTEM\MountedDevices] just before the install, then install the card, run fbreseal and power down the
    > > device. Open the image system hive offline and save the key content again. Analyze the differences (you can post the file here).
    > >
    > > - clean up \windows\setupapi.log file just before the IDE card installation. Then analyze the log after you see the error
    screen
    > > (again, please post the file here).
    > >
    > >
    > > Btw, are you building SP1 or SP2 XPe image?
    > >
    > > KM
    > >
    > > > KM,
    > > >
    > > > 1) Install IDE extension card but not use fbreseal.exe? Just reboot (power
    > > > up the device).
    > > > -> It's OK
    > > >
    > > > 2) Run the image through FBA with the IDE extension card and HDDs presented?
    > > > -> Also OK, but the same error occured after fbreseal.exe
    > > >
    > > > What's the problem? Help me
    > > >
    > > > David Gu
    > > >
    > > >
    > > > "KM" wrote:
    > > >
    > > >> David,
    > > >>
    > > >> What happens if you:
    > > >> 1) Install IDE extension card but not use fbreseal.exe? Just reboot (power up the device).
    > > >> 2) Run the image through FBA with the IDE extension card and HDDs presented?
    > > >>
    > > >> KM
    > > >>
    > > >> > hi all~
    > > >> >
    > > >> > I got a big problem using fbreseal.exe.
    > > >> >
    > > >> > In TD, I added fbreseal component, and set cmiResealPhase 0.
    > > >> > After FBA, I installed new IDE extention card, and connected to 4 new
    > > >> > HDDs.
    > > >> > Finally, running fbreseal.exe, and the system re-boots up, and the
    > > >> > error occured.
    > > >> >
    > > >> > Windows Product Activation:
    > > >> > A problem is preventing windows from accurately checking the license
    > > >> > for this computer. Error Code: 0x80090006
    > > >> >
    > > >> > It's not a problem of Boot Partition Setting on TD.
    > > >> > (It's already set correctly, 3072MB)
    > > >> >
    > > >> > If I ran fbreseal.exe without IDE extention card, There is no error.
    > > >> > All works is OK.
    > > >> >
    > > >> > What's the cause of this case?
    > >
    > >
    > >

  • Next message: david Gu: "Re: Error after executing fbreseal.exe; error code: 0x80090006"

    Relevant Pages

    • Re: Plug and play issue with Western Digital WD200
      ... Your XPe boots from new HDD. ... For installation to have effect PnP must restart current HDD driver. ... Depending on hardware type and serial numbers of that hardware you might ...
      (microsoft.public.windowsxp.embedded)
    • Re: BartPE wont boot from CD-ROM anymore
      ... If I disconnect the first HDD (the one with the Windows ... and Suse Linux systems), BartPE boots up fine. ... A DOS-CD with PowerQuest's DriveImage and PartitionMagic boots OK, ... and both programms show all disks and their partitions. ...
      (microsoft.public.windowsxp.general)
    • Re: Windows XP / HDD has trouble cold booting
      ... Clue number 1. ... > (due to not being able to read the HDD for some reason). ... It is only upon cold boot. ...
      (microsoft.public.windowsxp.general)
    • Re: zx5000 problems
      ... Linux live cd to another windows machine using samba. ... reinstall windows xp using a xp home sp2 disc i have not the repair disc ... The machine now boots into a black screen unless i press esc and choose ... settings to pick hdd first it still boots to the black screen. ...
      (comp.sys.hp.hardware)
    • Re: External HDD issues
      ... I haven't a clue what to do about your problem, ... One can have a HDD that the OS won't automount and so ... visible to Disk Utility. ... asking questions that seem relevant on the off chance that the extra ...
      (uk.comp.sys.mac)