Re: External hard drive

Tech-Archive recommends: Repair Windows Errors & Optimize Windows Performance

Thanks for all the advice. This just serves to confirm in my mind that there
was something very wrong with my new computer which has gone back for
warranty repair, because the "safely remove hardware" tool would always show
a message that the USB mass storage device was still busy even though it had
been inactive for ages. It never reached a point where it was "safe".
That's why I began to think it was correct to just flick the off switch. Then
it would produce "write delay failed" messages.

Glad to say this old faithful (slow) computer is working fine! Many thanks
again! This has all been a huge learning curve and these forums are such a
help.

"Uwe Sieber" wrote:


Yes, NTFS holds back some write accesses for a long time
period. Therefore it's a good idea to use the 'safe removal'
facility to flush all data.
The removal policy 'optimize for quick removal' is no help
because it has no effect on NTFS formatted drives.


Uwe




tess wrote:
Please advise me the correct way to disconnect my external hard drive which I
am using occasionally to access certain documents copied from my new computer
which has been taken in for warranty repair/replacement.

When I plug it into the USB port of this (old) computer, I flick on the
switch and it all works perfectly. When I'm finished with it, should I turn
off its power switch first, or use the "safely remove hardware" option first.
I noticed I got the following event log warning this morning and think I
only used the on/off switch.

Event Type: Warning
Event Source: Ftdisk
Event Category: Disk
Event ID: 57
Date: 2007/09/24
Time: 11:04:56 AM
User: N/A
Computer: PVT-2228B675042
Description:
The system failed to flush data to the transaction log. Corruption may occur.

For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 01 00 be 00 ......¾.
0008: 02 00 00 00 39 00 04 80 ....9..€
0010: 00 00 00 00 0e 00 00 c0 .......À
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

The computer shop where I bought it said I didn't need to use the "Safely
remove hardware" button but after the mess they've made of my new computer,
I'm not sure I believe them! Thanks for any advice.


.

Relevant Pages

  • Re: Upgrading Sony iDTV
    ... Going to the manual tuning ... I was able to tune the new channels through Manual Tune, but the stored channel wouldn't receive through the normal channel selection. ... This suggests to me the hardware is compatible but the firmware isn't. ... I'll try the service menu switch to 8k next time I visit, but it won't be until after phase 2. ...
    (uk.tech.digital-tv)
  • Re: Success! [ was Minimal 8-bit code for upd765 FDD initial program load]
    ... This was ONLY possible due to advice and assistance from many on this ... I came to this project very naive about computer hardware. ... I have learned a great deal about hardware and about CP/M ... provide rudimentary software debug - read/write/test ports and RAM. ...
    (comp.os.cpm)
  • Re: SBS2008 Monitor internet usage
    ... You'll want to look at hardware with that configuration. ... a good firewall to properly protect your network from the outside world. ... > connected to the switch as well. ...
    (microsoft.public.windows.server.sbs)
  • Re: New Linux computer
    ... I always used external modems (haven't used a modem since 95 I think, ... I can just switch the modem off. ... > Mostly hardware related, like fans failing and weak power supplies. ... the fan bearing is starting to get noisy and might need replacing ...
    (alt.os.linux.suse)
  • Re: broken re(4)
    ... OF>> The only hardware thing that is different in this system from the ... OF> In theory it could also be a power supply problem. ... OF> controller in that problematic machine drives the power ... The systems are all on the same switch, all devices show a 1GB link. ...
    (freebsd-stable)