Re: RDPCLIP.exe Stalled

Update:

Performed uninstall and reinstall of Terminal Services on the two problem
servers.

One is now back up with all printer and clipboard redirection capabilities
and RDPCLIP.exe is now running as a process. The other is still now working
so I am doing an uninstall of Terminal Services a third time on that one and
hopefully that one will heal up OK.

One hold-up. The notepad entry is still in the StartupPrograms value but
Notepad does not open on logon...don't know why not there. Perhaps the
Terminal Services installation is still partially broke...just not as broke
as beforehand.
"TP" wrote:

> Is this the only thing not working properly after
> your uninstall/reinstall?
>
> Some things below for you to check, hopefully
> they will help.
>
> What happens if you run rdpclip.exe manually? If
> things are normal it should start up and clipboard
> mapping should start working.
>
> What happens if you add notepad to the startupprograms?
>
> Temporarily change it to rdpclip,notepad
>
> The results should be that notepad starts up automatically
> when you logon.
>
> Is the fDisableClip set to 0 under
>
> HKLM\SYSTEM\CurrentControlSet\Control\Terminal Server\Winstations\RDP-Tcp
>
> If fDisableClip is set to 1 rdpclip.exe will terminate, because
> clipboard mapping is disabled.
>
> Check that rdpclip is still listed under Addins
>
> HKLM\SYSTEM\CurrentControlSet\Control\Terminal Server\Addins\Clip Redirector
>
> Name REG_SZ RDPClip
> Type REG_DWORD 0x00000003
>
> Thanks.
>
> -TP
>
> "Ralph Howarth" <RalphHowarth@xxxxxxxxxxxxxxxxxxxxxxxxx> wrote in message news:2EC962C1-4781-41C7-B1C1-6BE644C2816F@xxxxxxxxxxxxxxxx
> > Recently installed the HP 1200 Series Laserjet driver on a pair of Windows
> > 2000 Server SP4 machines. Immediately all printer redirection stopped...and
> > then later realized clipboard redirection was dead too. Uninstalled the
> > offending drivers from the Print Server Properties. A System Event persisted
> > even afterwards stating printer redirection had an internal error and failed.
> > Research on MSDN indicated to uninstall and reinstall terminal services on
> > the servers via Add / Remove Windows Components. Performed uninstall and
> > server rebooted. Now reinstalled terminal services.
> >
> > RDPCLIP.exe now does not load even though it exists in the system32 folder
> > and exists in the registry under the rdpwd key for StartupPrograms. This
> > condition is incidental for both the servers taht the offending printer
> > driver was once installed.
> >
> > Any suggestions?
>
>
>
.

Relevant Pages

  • Re: terminal server that hands out licenese to other servers..
    ... I have 100 servers. ... And I have 19 Terminal Services licenses. ... No CALs ...
    (microsoft.public.windows.terminal_services)
  • Re: TS Security Issue
    ... and acceptible connection methods (unless they're contractually obligated to ... terminal servers: ... Your Terminal Services Security Website ...
    (microsoft.public.windows.terminal_services)
  • Re: Event ID 1500, Your Profile can not be loaded
    ... The only information I have for this error is the KB link that recommends installing UPHClean. ... SDE - Terminal Services ... pre-SP1 servers or servers without UPHClean. ...
    (microsoft.public.windows.terminal_services)
  • Re: Security using terminal services
    ... > servers which require enhanced security. ... > reach these servers using terminal services unless the terminal services ... an IPSec filter list to block 3389 (the default RDP ... port) for all but the approved list of TS clients IP ...
    (microsoft.public.win2000.networking)
  • Re: Insane issue trying to launch an app... help please.
    ... Found a workaround - uninstall "Internet Explorer Enhanced Security ... trying to cross reference servers that work with servers that don't to ... I'm logged in as a domain admin, and I can perform other tasks that only a ... The installation app is located on my C:\ drive and all NTFS permissions are ...
    (microsoft.public.windows.server.general)