Re: DHCP Questions

I think - and take this with a grain of salt, as I am not familiar with your
firewall - you should hook up the T1 modem to the firewall, then the
firewall to the D-Link router, then all PCs to the router. That should
maximize protection and minimize exposure.

Unless you are putting the two network cards in the server on different
address ranges, disable one of them and leave it disconnected. You really,
REALLY don't want two network cards in the same address range in the same
server.

The only change I'd make to the above is if you are running a domain on your
network - if so, then disable DHCP on the router and turn it and DNS on
within the network. Otherwise let the router hand out addresses since this
is a much simpler set-up for a simple network.

--
Richard G. Harper [MVP Shell/User] rgharper@xxxxxxxxx
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* My website, such as it is ... http://rgharper.mvps.org/
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


"roubir" <roubir@xxxxxxxxx> wrote in message
news:1150653092.815187.66300@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Cool...

Thanks... But Once I enable DHCP on that server that I'm making the
DHCP What is the configuration... Does the T1 Modem plug directly in
the firewall then to the Server?

What about the D Link? I 'm i hooking that up to the switch? The DHCP
Server has two NIC Cards.. Does that assist in anything?

RM

Richard G. Harper wrote:
To add to Kurt's advice - "all those public static IPs" are not to worry
about. Those addresses will not be visible inside your network if it is
configured correctly. NAT should be turned on at the router to add a
layer
of protection between your network and the rest of the world.

--
Richard G. Harper [MVP Shell/User] rgharper@xxxxxxxxx
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* My website, such as it is ... http://rgharper.mvps.org/
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


"roubir" <roubir@xxxxxxxxx> wrote in message
news:1150607335.328194.193390@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Okay... Here it is...

I'm doing work for my church and I have a T-1 Modem By Netopia....
And A firewall Sonicwall
And a D-LINK Router ... (Which I want to disable DHCP and use as a
Wireless AP Only)
I want to setup DHCP Through a Windows 2000 Server Box.. It has 2 NIC
Cards... How can I go about doing this setup? Also I have three servers
E-mail Exchange- DNS those all however have Public Static IP'S that I
cannot Change.... Can someone help? Thanks

rob




.

Relevant Pages

  • << SBS News of the week - Sept 26 >>
    ... And he points to the info you need to put the file on the server in the ... at the network perimeter. ... The Symantec Firewall/VPN and the Gateway Security ... by the firewall at risk. ...
    (microsoft.public.backoffice.smallbiz)
  • << SBS News of the week - Sept 26 >>
    ... And he points to the info you need to put the file on the server in the ... at the network perimeter. ... The Symantec Firewall/VPN and the Gateway Security ... by the firewall at risk. ...
    (microsoft.public.backoffice.smallbiz2000)
  • << SBS News of the week - Sept 26 >>
    ... And he points to the info you need to put the file on the server in the ... at the network perimeter. ... The Symantec Firewall/VPN and the Gateway Security ... by the firewall at risk. ...
    (microsoft.public.windows.server.sbs)
  • Re: need help re. office network install
    ... > and their network is a mess, the result of years of neglect. ... they have a gateway server w/ no special ... > firewall rules on it, they have a large DMZ that serves no purpose ... install anymore software on the firewall machine than is absolutely ...
    (comp.os.linux.networking)
  • Re: oops again
    ... open on the Firewall, and the default should be none. ... Since you intend to install IIS purely as a test server for your ASPX pages ... Make sure that IIS is only listening on the local network (192.168.x.y ...
    (microsoft.public.inetserver.iis)