Re: NIC Config Gots Lost

Tech-Archive recommends: Repair Windows Errors & Optimize Windows Performance

From: Ashish Bagla (abagla_at_webbyte.com)
Date: 09/11/04 

Date: Sat, 11 Sep 2004 09:31:50 +0530

I have tried 2 different NIC's in2 diff slots.

Even if the canble is un plugged & the cards ip address is 192.168.0.1 it
will respond to self ping.

If responds for approx 30 secs after the card is activated & then the error
comes saying connection failed...

Ashish

"Richard G. Harper" <rgharper@email.com> wrote in message
news:OAXfAX4lEHA.3260@TK2MSFTNGP09.phx.gbl...
> Have you tried a new network card, new cable, or different jack on your
> networking device?
>
> --
> Richard G. Harper [MVP Win9x] rgharper@email.com
> * PLEASE post all messages and replies in the newsgroups
> * for the benefit of all. Private mail is usually not replied to.
> * HELP us help YOU ... http://www.dts-l.org/goodpost.htm
>
>
> "Ashish Bagla" <abagla@webbyte.com> wrote in message
> news:OusAgi2lEHA.3632@TK2MSFTNGP09.phx.gbl...
> P.S. : When I try to enable teh NIC it gets enabled for couple of seconds
&
> during that time it is pingable but immi after that it beocmes non
pingable
> & says connection failed in the NIC enabling box.
>
>
> "Ashish Bagla" <abagla@webbyte.com> wrote in message
> news:%23M5a3Q2lEHA.1008@tk2msftngp13.phx.gbl...
> Event Log also says
> " The Routing and Remote Access service depends on the NetBIOSGroup
group
> and no member of this group started. "
>
> " SAM failed to start the TCP/IP or SPX/IPX listening thread "
>
> Event Source: NetBT
> Initialization failed because the transport refused to open initial
> Addresses.
>
>
>
> "Ashish Bagla" <abagla@webbyte.com> wrote in message
> news:er2dg61lEHA.3612@TK2MSFTNGP12.phx.gbl...
> > Event log says the following
> >
> > Description:
> > The system detected that network adapter Realtek RTL8139(A) PCI Fast
> > Ethernet Adapter #3 was disconnected from the network, and the
adapter's
> > network configuration has been released. If the network adapter was
not
> > disconnected, this may indicate that it has malfunctioned. Please
> contact
> > your vendor for updated drivers.
> >
> > "Ashish Bagla" <abagla@webbyte.com> wrote in message
> > news:%23G9SQ21lEHA.3988@tk2msftngp13.phx.gbl...
> > > When I disable & enable my lan card it works fine for 30 secs & immi
> after
> > > that it losts its ip address & other confis...
> > >
> > > Ethernet adapter Local Area Connection:
> > >
> > > Connection-specific DNS Suffix . :
> > > Description . . . . . . . . . . . : Realtek RTL8139(A) PCI
> Fast
> > > Ethernet
> > > Adapter #3
> > > Physical Address. . . . . . . . . : 00-40-F4-82-F0-1D
> > > DHCP Enabled. . . . . . . . . . . : No
> > > IP Address. . . . . . . . . . . . : 192.168.0.1
> > > Subnet Mask . . . . . . . . . . . : 255.255.255.0
> > > Default Gateway . . . . . . . . . :
> > > DNS Servers . . . . . . . . . . . :
> >
>

> --------------------------------------------------------------------------
> > --
> > > ---------
> > > Immi after 30 secs or so... it shows...
> > >
> > > Ethernet adapter Local Area Connection:
> > >
> > > Media State . . . . . . . . . . . : Cable Disconnected
> > > Description . . . . . . . . . . . : Realtek RTL8139(A) PCI
> Fast
> > > Ethernet
> > > Adapter #3
> > > Physical Address. . . . . . . . . : 00-40-F4-82-F0-1D
> > >
> > >
> >
> >
>
>

Relevant Pages

  • Re: Old Network card still exists after upgrade - how to remove
    ... PLEASE post all messages and replies in the newsgroups ... > using the same PCI card ... all network settings were lost. ... > hardware devices for the machine, and its not in network properties. ...
    (microsoft.public.windowsxp.network_web)
  • Re: No DCHP, static works fine
    ... Have you tried to sniff the traffic produced by the card? ... > get the following events in my System Event log: ... > "Your computer was not able to renew its address from the network ... > 3) Uninstalled card through device manager, rebooted, same problem. ...
    (microsoft.public.windowsxp.network_web)
  • Event Error Log
    ... Your computer has automatically configured the IP address for the Network ... Card with network address xxE0xxxxxE1F. ... .When I go to Microsoft to look for an explanation, ... Event Log Messages or Knowledge Base databases at this time. ...
    (microsoft.public.windowsxp.security_admin)
  • Re: Dropping internet connection
    ... your network adapter manufacturer has a test program to test the network ... Test the card by substitution if not. ... PLEASE post all messages and replies in the newsgroups ...
    (microsoft.public.windowsxp.network_web)
  • Re: This Device Cannot Start Error Message
    ... * PLEASE post all messages and replies in the newsgroups ... > message related to my network adpater card which is a Linksys EtherFast ...
    (microsoft.public.windowsxp.network_web)